Pages: [1]   Go Down

AuthorTopic: Urgent Help Needed  (Read 1495 times)

0 Members and 1 Guest are viewing this topic.

Offline steve prosser

  • Posts: 64
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Urgent Help Needed
« on: November 15, 2005, 20:12:25 »
Been working fitting new springs and shockers to the RR yesterday and today.
Fronts done no problem
Started on rears today, took shocker off went to unbolt the spring retainer, 1 bolt snapped the other rounded the corners off!!! Great start!
after a few mins wondering quite how to drill them out, noticed the the bracket on the axle casing was falling apart(no metal just Rust), with a pull on the spring the whole lot fell off!!!!!!!
OHHH SH?T!!!!
On inspection the other side is the same
Im sure im not the first to have this happen to them
Hows anyone got over this?
Your help and advise will be gratefully recieved
Logged

Offline paul_humphreys

  • Posts: 2181
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Urgent Help Needed
« Reply #1 on: November 15, 2005, 21:12:13 »
You have to make them up and weld them on. Or get another axel.
Logged
LC 80 series 1993. 285/75/16s Cooper STTs, OME 850s on the front with 25mm packer, 868s on the rear. 4.88 diffs. Winch bumper with 12000lb winch. Factory lockers. HD rear bumper with wheel carrier and winch mount.

http://www.crag-uk.org

Offline Range Rover Blues

  • Moderator
  • ***
  • Posts: 15218
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +3/-0
    • South Yorkshire
  • Referrals: 0
Urgent Help Needed
« Reply #2 on: November 16, 2005, 02:06:59 »
Probably just as well you caught it when you did.
Logged
Blue,  1988  Range Rover 3.5 EFi with plenty of toys bolted on
Chuggaboom, 1995 Range Rover Classic
1995 Range Rover Classic Vogue LSE with 5 big sticks of Blackpool rock under the bonnet.

Offline Dave

  • Posts: 1046
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 1
Urgent Help Needed
« Reply #3 on: November 16, 2005, 17:15:54 »
You are lucky to have court it and not had it come of going round an island or somewhere similar.  I had the front go, panard bracket snap on me. I found it was as easy to get a second hand axel, there are some on ebay.
Logged
DAVE
MUD-CLUB MEMBER 333

 Disco TDI 1998
 Disco TDI 1993    K333 MUD
 Disco TDI 1994
 90  N/A soon to be TDI 1993
 Series 3 1971
 R33 Skyline GTS-T

Offline MuddyMike

  • Posts: 391
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
    • Leyburn, N. Yorkshire
  • Referrals: 0
Urgent Help Needed
« Reply #4 on: November 16, 2005, 19:45:23 »
When mine went the same way I fabricated new ones from bits of steel and welded them on in situ.

Mike
Logged
If you can't get there in a Land Rover you can't get there

Self built Range Rover/Lightweight hybrid (yes the one with yellow wheels)

Offline Xtremeteam

  • Regional Rep
  • *
  • Posts: 6476
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Its just the way i roll
    • lampeter, west wales
  • Referrals: 0
Urgent Help Needed
« Reply #5 on: November 16, 2005, 19:53:02 »
IIRC i seen the spring platforms advertised in one of the mags along with the rear shockie mounts
Logged
Mike
I can Drive.. You can criticize..
I too can criticize like you.. but can you Drive like me??

Offline steve prosser

  • Posts: 64
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Urgent Help Needed
« Reply #6 on: November 16, 2005, 20:12:57 »
Spent all afternoon today getting it sorted
Removed what was left of the orginal brackets
had 2 brackets made from some nice thick channel section
then welded securly in place.
new springs and shockers on
job sorted!!!!!
Very glad we found it now and not stuck down a lane somewhere miles from anywhere!!!

Thanks for all your comments
Just waiting for the new tyres now!!!!!
Logged
Pages: [1]   Go Up
 





SimplePortal 2.3.5 © 2008-2012, SimplePortal