Topic: 200TDi Bumpers (Read 1575 times)

Rangie3.0LtrDan · « **on:** March 05, 2006, 16:16:23 »

Has anyone got any pictures of the cut down bumpers, i.e. missing the lower valance as i am just about to attempt mine but i dont know where to start, also just need to see the corner bits as obviously i dont know where to cut them either!

I need to get this done by the latest tomorrow :D

Cheers

Dan

Pike · « **Reply #1 on:** March 05, 2006, 18:39:41 »

unfasten the lower valance,its on fiddly screws underneath,i think theres about 6 and then draw a line with a felt pen in line with the bottom of the bumper and cut it off either with a grinder or a saw

Damonski · « **Reply #2 on:** March 05, 2006, 18:49:00 »

Sort of like this :

I just followed the bottom of the bumper round the corners and chopped.

Matt_H · « **Reply #3 on:** March 05, 2006, 18:51:05 »

It the back of my 90 for the tip trip tomorrow is two ready cut bumper ends and a bumper...

Yours if you want em (or anyone elses).... you must come and collect by the weekend though...

PM responses before tomorrow morning else they are going to get binned :)

Matthew

Rangie3.0LtrDan · « **Reply #4 on:** March 05, 2006, 18:54:59 »

Matt stick me name on em :D hehe, can collect wednesday when meeting for lunch ;) think of defender seat cost savings ;)

Dan

Matt_H · « **Reply #5 on:** March 05, 2006, 20:53:20 »

he doesn't want them now - so anyone else shout now!

M

muddyjames · « **Reply #6 on:** March 13, 2006, 15:36:27 »

cut mine ages ago just before you said you had some trimmed down ones :(

Did you trim them in the end Dan?

I used a stanley knife for mine and followed the bit where the bumper cap steps down slightly. Mine is a 300tdi though.

pics in my gallery of mine.

rustprooflandyracer · « **Reply #7 on:** March 13, 2006, 17:35:28 »

Are you are able to leave the middle section in place containing the No. plate... You probably are just wanted to check. Then off to buy a good stanley knife.

Cheers Matt

Damonski · « **Reply #8 on:** March 13, 2006, 17:45:45 »

yes you if you put your head under the front end, that number plate mount is only held on with two small screws.

You'll need more than a stanley knife tho, its quite tuff and thick plastic. I nice little hacksaw would do the job better. I used a coping saw with a wood blade to do mind, the coping saw allowed it to follow the contour better and reached the middle from both ends of the end caps.

muddyjames · « **Reply #9 on:** March 13, 2006, 18:06:53 »

a brand new stanley knife blade and a ruler to score the line lightly for the first time and then after that the blade follows that line. I managed to do both end caps with 1 blade. The blade was very blunt though by the end of it.

It left a wonderful smooth edge too once cut.

Yes you can leave the plastic bit in place for the number plate. I broke a screw mount though when I did mine and so drilled 2 holes in the botom of it and into the bumper and put 2 screws in it. also means it is quick to remove if I need the high lift jack points on my steering guard and dont need to get muddy underneath. I dont have a high lift jack so wont be very often I need to take it off.

Jake · « **Reply #10 on:** March 13, 2006, 18:24:18 »

You can see where i cut my end cap by clicking HERE

Another picture of the complete front bumper can be found by clicking HERE
I did mine with a nice sharp stanley knife.
Easy
:D

muddyjames · « **Reply #11 on:** March 13, 2006, 18:28:50 »

I think it was you Jake who suggested the stanley knife to me.

Jake · « **Reply #12 on:** March 13, 2006, 18:32:39 »

It may well have been

News:

AuthorTopic: 200TDi Bumpers (Read 1575 times)

Rangie3.0LtrDan

200TDi Bumpers

Pike

200TDi Bumpers

Damonski

200TDi Bumpers

Matt_H

200TDi Bumpers

Rangie3.0LtrDan

200TDi Bumpers

Matt_H

200TDi Bumpers

muddyjames

200TDi Bumpers

rustprooflandyracer

200TDi Bumpers

Damonski

200TDi Bumpers

muddyjames

200TDi Bumpers

Jake

200TDi Bumpers

muddyjames

200TDi Bumpers

Jake

200TDi Bumpers