Pages: [1]   Go Down

AuthorTopic: The basics of winch mounting...  (Read 1686 times)

0 Members and 1 Guest are viewing this topic.

Offline Jimbo

  • Posts: 1126
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
The basics of winch mounting...
« on: April 12, 2006, 12:13:28 »
Not how to, but how do I (please !)

I'm assuming that all winch mounts (be they bumpers, plates or whatever) only fix to the existing (factory) bumper to chassis mounting points. If this is so (and in basic, laymans terms) can I mount my winch onto a big lump of steel plate, and then mount that onto the front of the 110, using the bumper to chassis mounting points ?

What I want to achieve is a more discrete system for mounting my RPH8000 hydraulic, as at the moment it's on a huge, industrial galvanised bumper/girder thing - which sticks out 12" from the front of the truck.

I have seen ads for 'winch mounting trays', can I assume that these are big lumps of steel plate (my laymans terms again) that bolt onto the chassis/bumper points. Would I then be able to fit a standard Defender bumper on as well ?

I'm also planning (assuming that the 'tray' thing works) on cutting the front grille so that the winch gets recessed back towards the radiator as far as poss - thus improving my non-existent approach angle !

Ta,
Jim
Logged
Jim

TDV6 HSE D3
Defender 110 Td5 Hard top, BFG MT's, and no EGR either

http://www.hertfordshire4x4response.net

Offline Jimbo

  • Posts: 1126
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
The basics of winch mounting...
« Reply #1 on: April 12, 2006, 12:15:11 »
Logged
Jim

TDV6 HSE D3
Defender 110 Td5 Hard top, BFG MT's, and no EGR either

http://www.hertfordshire4x4response.net

Offline bullfrog

  • Posts: 1009
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
The basics of winch mounting...
« Reply #2 on: April 12, 2006, 19:47:17 »
Crickey, You were not kidding ! :shock:
A plate mounted to the chassis would work well and allow you to move the winch back a bit.
I would say 6mm plate as a minimum with large washers on all mounting points.
Logged

Offline Range Rover Blues

  • Moderator
  • ***
  • Posts: 15218
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +3/-0
    • South Yorkshire
  • Referrals: 0
The basics of winch mounting...
« Reply #3 on: April 24, 2006, 02:24:10 »
Holy smoke that looks like an armoured truck!

Part of the thing with 6mm steel in winch bumpers is because they are spanning a large area with flat plates of steel, with little reinforcing.  Th3e chaasis you are bolting to is made of much thinner steel but beacuase it's a box section it is inherantly strong.

The weakest link will often be the mounting points, not the bolts themselves but the erea around them, probably on the winch plate (which I'd prefer).

If you consider how much (read how little) strength there is is say a JATE ring mounting and yet you can safely winch onto one, you get some idea of how big the overkill is one winch bumpers.  Mostly because the winch pulls off-line with the base plate and generates a huge bending force in it.

Anyway, how does this help you, well I find that most winch bumpers use the bumper mounts plus a 3rd bolt either side through a hole level with the front body mount (RRC and Disco especially) although a stronger mount would be the steering boc tie-bar mount and it's redundant friend on the LHS, just check out a pair of Jack-Mates if you can't picture it.  Anyway, these mounting points should be adequately strong for your winch with a well designed winch tray.

I have a demountable winch in a back-rack from Goodwinch and you should see how little metal is required, yet it is rated at 9,000lb.
Logged
Blue,  1988  Range Rover 3.5 EFi with plenty of toys bolted on
Chuggaboom, 1995 Range Rover Classic
1995 Range Rover Classic Vogue LSE with 5 big sticks of Blackpool rock under the bonnet.

Offline Jimbo

  • Posts: 1126
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
The basics of winch mounting...
« Reply #4 on: April 24, 2006, 08:07:43 »
Cheers for the replies.

It looks like I'm going to buy the 'build-your-own' bumper bits from Southdown (ala Dave Landy's 90), and then modify the winch tray to take the Ramsey winch - which reminds me, Dave...PM for you !

Jim
Logged
Jim

TDV6 HSE D3
Defender 110 Td5 Hard top, BFG MT's, and no EGR either

http://www.hertfordshire4x4response.net

Offline ProjectBlue

  • Posts: 36
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
The basics of winch mounting...
« Reply #5 on: May 05, 2006, 15:53:10 »
Jimbo, that bumper you've pictured is Electricity/Water board spec. If you look around some of the dealers selling ex authority Defenders you may find one thats been taken off going cheap.
Logged
Come kneel with me in the Chapel of Solihull and worship at the altar of the Green Oval

Offline Jimbo

  • Posts: 1126
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
The basics of winch mounting...
« Reply #6 on: May 05, 2006, 18:11:18 »
Quote from: "ProjectBlue"
Jimbo, that bumper you've pictured is Electricity/Water board spec. If you look around some of the dealers selling ex authority Defenders you may find one thats been taken off going cheap.


PB, my 110 is ex-leccy board, with the galvanised girder bolted on the front - I'm looking to replace it (the winch bumper) with something slightly more descrete !

I have several ideas in the mix at the moment, all of which have their pros and cons...........I'm still contemplating !

Jim
Logged
Jim

TDV6 HSE D3
Defender 110 Td5 Hard top, BFG MT's, and no EGR either

http://www.hertfordshire4x4response.net

Offline Stuart

  • Posts: 23
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
winch
« Reply #7 on: May 06, 2006, 18:01:50 »
I've got an ex electricity board hydraulic winch for sale, i think its rated at 12000lbs may save time and money but were is the the fun in buying one. Good luck let us know how you get on
Logged

Offline Jimbo

  • Posts: 1126
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
The basics of winch mounting...
« Reply #8 on: May 07, 2006, 16:09:29 »
Stuart,

I've got the winch too - hydraulic Ramsey RPH8000, just looking for alternative ways to mount it !

Jim
Logged
Jim

TDV6 HSE D3
Defender 110 Td5 Hard top, BFG MT's, and no EGR either

http://www.hertfordshire4x4response.net

Offline Stuart

  • Posts: 23
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
winch
« Reply #9 on: May 07, 2006, 16:25:51 »
sorry for confusion, still good luck though :lol:
Logged

Offline ProjectBlue

  • Posts: 36
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
The basics of winch mounting...
« Reply #10 on: May 09, 2006, 15:41:19 »
:D  oops, I didn't read that properly sorry  :oops:
Logged
Come kneel with me in the Chapel of Solihull and worship at the altar of the Green Oval
Pages: [1]   Go Up
 





SimplePortal 2.3.5 © 2008-2012, SimplePortal