Pages: [1]   Go Down

AuthorTopic: lifting trouble  (Read 705 times)

0 Members and 1 Guest are viewing this topic.

Offline scouse lanny

  • Posts: 79
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
lifting trouble
« on: September 24, 2006, 19:42:48 »
hi there can anyone help a friend has just fitted a 2 inch lift kit with blue springs and pro comp shocks but it has pushed the front up but the back hasent changed do u think they have sold him wrong springs
Logged
kevin walsh

Offline gtomo2

  • Posts: 1924
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
lifting trouble
« Reply #1 on: September 24, 2006, 19:54:11 »
Could be rear anti roll bar pulling it down? If he still has it fitted. Took mine off when i fitted a 1 inch lift as it didnt sit right with it on
Logged
Mr Graeme Thomas (tomo)
300 TDi Discovery - So i can go fording
Stop laughing put the camera down AND PASS ME THE TOW ROPE !! PLEASE

Offline way2deep

  • Posts: 850
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
lift
« Reply #2 on: September 24, 2006, 20:02:50 »
he did put the right ones on the front and back ???? small at the front large at the rear  :D
Logged
robbie
200 tdi rangie  1989  4dr

Offline Xtremeteam

  • Regional Rep
  • *
  • Posts: 6476
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Its just the way i roll
    • lampeter, west wales
  • Referrals: 0
Re: lift
« Reply #3 on: September 24, 2006, 21:48:55 »
Quote from: "way2deep"
he did put the right ones on the front and back ???? small at the front large at the rear  :D

was just gonna say that  :lol:
Logged
Mike
I can Drive.. You can criticize..
I too can criticize like you.. but can you Drive like me??

Offline scouse lanny

  • Posts: 79
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
springs
« Reply #4 on: September 24, 2006, 22:16:35 »
i was thinking they could off just give them any ones wont b going there again  :lol:
Logged
kevin walsh

PUX

  • Guest
lifting trouble
« Reply #5 on: September 24, 2006, 22:38:36 »
defo wrong way round lol
Logged

Offline driftwood

  • Posts: 421
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
lifting trouble
« Reply #6 on: September 24, 2006, 23:06:38 »
take it off and check the overall sizes from the origional ones, if they are bigger jack the shassis up and make shure the axel droppes enough. you may have a siezed centre linkage, theres 2 bars going from the axel at the back that go up onto the body area just infront of the fuel tank. i had this problem and the springs were ok. after a good douse in wd40 and a trip to waddon it freed itself.....just a thought :wink:
Logged

Offline way2deep

  • Posts: 850
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: springs
« Reply #7 on: September 24, 2006, 23:42:46 »
i was thinking they could off just give them any ones wont b going there again  :lol:[/quote]
where did  ya get them from ????????????????? bearing in mind too that if they are pro comp springs they should be marked up n/s and o/s for the front springs ...also the o/s spring is fractionally longer than the n/s one
Logged
robbie
200 tdi rangie  1989  4dr

Offline scouse lanny

  • Posts: 79
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
lifting
« Reply #8 on: September 25, 2006, 21:45:38 »
no thehocks a pro comp i think the springs ar bear mach but he said there was no difference in height on all the springs when he got them i thought the bac should b longer it was lr centre in liverpool
Logged
kevin walsh
Pages: [1]   Go Up
 





SimplePortal 2.3.5 © 2008-2012, SimplePortal