AuthorTopic: Steering drop arm  (Read 784 times)

0 Members and 1 Guest are viewing this topic.

Offline Sharpshooter

  • Posts: 1484
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Steering drop arm
« on: October 01, 2006, 18:54:32 »
Does anyone know if all defender/rangerover drop arms are re-furbishable? Mines shot, and i have a kit, but without taking it off, i would like to know. It is an early 3 bolt rangie box.

Cheers. :)

Offline V8MoneyPit

  • Moderator
  • ***
  • Posts: 5077
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +1/-0
  • Referrals: 0
Steering drop arm
« Reply #1 on: October 02, 2006, 17:28:58 »
The ball joint is replaceable on all of them, but if the splines gone, buy a new one.

Only £26.00 + VAT from Paddocks.
Rgds
Steve

"Reality is wrong. Dreams are for real."

Land Rover build:
www.daisythediesel.com

Photos (my other passion and weakness):
http://www.flickr.com/photos/v8moneypit/

Offline Sharpshooter

  • Posts: 1484
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Steering drop arm
« Reply #2 on: October 02, 2006, 18:47:07 »
No, its definately the ball joint. :)

Just wanted to make sure before i rip it off. :)

Have had the ball joint for months, but just keep putting it off. I have about an eighth of a turn play in the wheel now. :(

Offline Range Rover Blues

  • Moderator
  • ***
  • Posts: 15218
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +3/-0
    • South Yorkshire
  • Referrals: 0
Steering drop arm
« Reply #3 on: October 03, 2006, 13:16:06 »
:o  OOOhh, not nice.

You can change the balljoint wihtou removing the drop arm, but it's fiddly.  Remeber, Dremel grinds :wink:

I use a G clamp with 2 sockets, one a deep socket.
Blue,  1988  Range Rover 3.5 EFi with plenty of toys bolted on
Chuggaboom, 1995 Range Rover Classic
1995 Range Rover Classic Vogue LSE with 5 big sticks of Blackpool rock under the bonnet.

Offline V8MoneyPit

  • Moderator
  • ***
  • Posts: 5077
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +1/-0
  • Referrals: 0
Steering drop arm
« Reply #4 on: October 03, 2006, 16:39:12 »
I support a socket on a small jack under the arm to compress the spring to remove the circlip.
Rgds
Steve

"Reality is wrong. Dreams are for real."

Land Rover build:
www.daisythediesel.com

Photos (my other passion and weakness):
http://www.flickr.com/photos/v8moneypit/

Offline Sharpshooter

  • Posts: 1484
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Steering drop arm
« Reply #5 on: October 03, 2006, 17:58:14 »
Well. So much for all drop arms being refurbishable. I got it off, and then found that the cap that holds the guts in was peened over. Got it back, and no groove for the circlip.
So i ended up holding it all in place with a vice, and tig welding the plate on the back.

Has done the trick. :D

Offline hobbit

  • Posts: 4750
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Steering drop arm
« Reply #6 on: October 04, 2006, 13:29:21 »
until the box goes, you can change the arms to the other type and then change the fitment on the link arm, so that it works off a standard track rod end type fitment

I did this on the disco the other year, it eleminates the problem of chasing springs around under the vehicle, this is as long as you have the room to fit the other type of arm in its place
Kev

'91 stretch Discovery 200 Tdi
Hybrid for running round (got to go now)
Srs 3 Lightweight petrol (got to go)
Srs 3 Lightweight petrol, runabout

Not every problem can be solved with duct tape, and it's exactly for those situations we have WD 40

Offline V8MoneyPit

  • Moderator
  • ***
  • Posts: 5077
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +1/-0
  • Referrals: 0
Steering drop arm
« Reply #7 on: October 04, 2006, 16:29:16 »
Quote from: "SHARPSHOOTER"
Well. So much for all drop arms being refurbishable. I got it off, and then found that the cap that holds the guts in was peened over. Got it back, and no groove for the circlip.


That's a surprise to me. Oh well, you learn something new every day!
Rgds
Steve

"Reality is wrong. Dreams are for real."

Land Rover build:
www.daisythediesel.com

Photos (my other passion and weakness):
http://www.flickr.com/photos/v8moneypit/

Offline Sharpshooter

  • Posts: 1484
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Steering drop arm
« Reply #8 on: October 04, 2006, 17:11:32 »
Quote from: "V8MoneyPit"
Quote from: "SHARPSHOOTER"
Well. So much for all drop arms being refurbishable. I got it off, and then found that the cap that holds the guts in was peened over. Got it back, and no groove for the circlip.


That's a surprise to me. Oh well, you learn something new every day!


Theres always one different. It always seems to be mine though. :) :)

 






SimplePortal 2.3.5 © 2008-2012, SimplePortal