Pages: [1]   Go Down

AuthorTopic: timing a 2.5td  (Read 10396 times)

0 Members and 1 Guest are viewing this topic.

Offline davidlandy

  • Posts: 3568
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
timing a 2.5td
« on: November 17, 2004, 21:05:17 »
A friend has a 2,5td which has thrown its cam belt.

who can advise on how to time it up again? (Guy?)

tried lining up the dots and arrows like the haynes lies book says but when you turn it over it locks up - feels like a piston hitting a valve. hmmm

help  - thanks
Logged
Dave
Sniff, sniff, this mud smells funny

Offline muddyweb

  • Posts: 6382
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
timing a 2.5td
« Reply #1 on: November 17, 2004, 21:09:39 »
You need to make sure you start from TDC with everything.  Not difficult to get the camshaft in the wrong place (with the dots lined up)
Logged
Tim Burt
Muddyweb
-------------------------------------------------------------------------------------------------------------------
www.muddyweb.com
-------------------------------------------------------------------------------------------------------------------

Offline Guy90

  • Posts: 1844
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
timing a 2.5td
« Reply #2 on: November 17, 2004, 23:34:14 »
Dave,

Was that why Jason was trying to ring me tonight? I had no luck with this and got the same thing. And that was after setting TDC. Gave up in the end and took it to garage. Never did get all the dots to line up :cry:  :cry: .

guy
Logged

Offline davidlandy

  • Posts: 3568
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
timing a 2.5td
« Reply #3 on: November 18, 2004, 09:53:22 »
Yes Guy  it was  - the thinking being that you had been there so may know what to do! :oops:

Tim,

Getting the dots lined is a nightmare - would it being one notch out cause the whole thing to lock ?

also the cam pulley dot is lined up with the arrow on the casing but when we peer through at the valves on no1 they are open not both closed - is that right

 :?:  :?:  :?  :?
Logged
Dave
Sniff, sniff, this mud smells funny

Offline muddyweb

  • Posts: 6382
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
timing a 2.5td
« Reply #4 on: November 18, 2004, 18:32:25 »
Being one notch out could well cause a valve and piston to meet, yes.

I can't remember the exact procedure, as it's been about 18 months since I did a TD, but you need to get the piston at TDC on (I think) the compression stroke, which would mean both valves closed.

I'll see if I can dig out the manual and confirm that.
Logged
Tim Burt
Muddyweb
-------------------------------------------------------------------------------------------------------------------
www.muddyweb.com
-------------------------------------------------------------------------------------------------------------------

Offline davidlandy

  • Posts: 3568
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
timing a 2.5td
« Reply #5 on: November 18, 2004, 18:33:22 »
cheers Tim
Logged
Dave
Sniff, sniff, this mud smells funny

Offline Range Rover Blues

  • Moderator
  • ***
  • Posts: 15218
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +3/-0
    • South Yorkshire
  • Referrals: 0
timing a 2.5td
« Reply #6 on: November 20, 2004, 14:42:59 »
Quote from: "muddyweb"
Being one notch out could well cause a valve and piston to meet, yes.

I can't remember the exact procedure, as it's been about 18 months since I did a TD, but you need to get the piston at TDC on (I think) the compression stroke, which would mean both valves closed.

I'll see if I can dig out the manual and confirm that.


Surely on a 4-cylinder it's the valves that decide whether TDC is compression or exhaust/inlet overlap.
Logged
Blue,  1988  Range Rover 3.5 EFi with plenty of toys bolted on
Chuggaboom, 1995 Range Rover Classic
1995 Range Rover Classic Vogue LSE with 5 big sticks of Blackpool rock under the bonnet.

Offline diesel_boy

  • Posts: 362
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • NUTTER
  • Referrals: 0
timing a 2.5td
« Reply #7 on: November 20, 2004, 18:47:21 »
TELL JASON ITS KWANED   (JUST REARANGE THE LETTERS)  AND THROW IT IN THE BIN  :lol:  :lol:  :lol:  :twisted:
Logged
2door rangie beeing bob'erd    
http://members.mud-club.com/profiles/diesel_boy
sam@northants4x4.com

Offline MUSKIE

  • Posts: 232
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
timing a 2.5td
« Reply #8 on: November 20, 2004, 20:48:58 »
is that massive wheels on a 90 jason or someone else :?:
Logged

Offline davidlandy

  • Posts: 3568
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
timing a 2.5td
« Reply #9 on: November 21, 2004, 17:23:31 »
discovered this afternoon that it needs 4 push rods and a rocker

any ideas where we can get these from (cheap of course) ????

cheers
Logged
Dave
Sniff, sniff, this mud smells funny

Offline Guy90

  • Posts: 1844
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
timing a 2.5td
« Reply #10 on: November 21, 2004, 21:47:49 »
I told him when it happened to check the push rods and rockers :roll:  :roll: .

I got mine from Craddocks. They were pretty cheap as I remember.

Guy
Logged

Offline davidlandy

  • Posts: 3568
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
timing a 2.5td
« Reply #11 on: November 21, 2004, 21:53:41 »
did they have themn in stock or did you have to order?

ps - dont spose my, i mean your, steering guard managed to straighten itself did it?  (heres hoping)

 :D
Logged
Dave
Sniff, sniff, this mud smells funny

Offline Guy90

  • Posts: 1844
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
timing a 2.5td
« Reply #12 on: November 21, 2004, 22:17:59 »
Quote from: "davidlandy"
did they have themn in stock or did you have to order?

They had them in stock.

ps - dont spose my, i mean your, steering guard managed to straighten itself did it?  (heres hoping)

 :D


Er no! Found the spot where I bent it the first time and then did it it again  :oops:  :lol:  :lol:

Guy
Logged
Pages: [1]   Go Up
 





SimplePortal 2.3.5 © 2008-2012, SimplePortal