Pages: [1]   Go Down

AuthorTopic: Rear Floor  (Read 1948 times)

0 Members and 1 Guest are viewing this topic.

Offline 90sam

  • Posts: 265
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Rear Floor
« on: March 28, 2007, 16:24:21 »
Ive just bought a 90 and it has a rusty boot floor, does it need to be replaced or will it be okay with just some sealant over the holes?!?
How much would it cost to be repaired approx?

Logged

Offline davidlandy

  • Posts: 3568
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Rear Floor
« Reply #1 on: March 28, 2007, 16:30:45 »
I would leave it in and just over lay it with a sheet of chequerplate
Logged
Dave
Sniff, sniff, this mud smells funny

Offline hobbit

  • Posts: 4750
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Rear Floor
« Reply #2 on: March 28, 2007, 17:49:30 »
Quote from: "davidlandy"
I would leave it in and just over lay it with a sheet of chequerplate


Agreed
Logged
Kev

'91 stretch Discovery 200 Tdi
Hybrid for running round (got to go now)
Srs 3 Lightweight petrol (got to go)
Srs 3 Lightweight petrol, runabout

Not every problem can be solved with duct tape, and it's exactly for those situations we have WD 40

Offline 90sam

  • Posts: 265
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Rear Floor
« Reply #3 on: March 28, 2007, 17:54:10 »
So it wouldnt fail an mot with it like that?
Logged

Offline TechnoTurkey

  • Posts: 707
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Rear Floor
« Reply #4 on: March 28, 2007, 18:54:19 »
Fine for MOT as its not structural.  Just corrosion between the alu floor and steel chassis.  I would douse the chassis with waxoyl while you can see it through the hole though.
Logged
2007 Honda Civic Type R GT
1982 VW Camper - Current Project
1991 Pajero SWB 2.5TD - SOLD
1990 Range Rover Vouge 3.9 V8 - SCRAPPED
1989 110 3.5 V8 CSW - SOLD
1984 Series 3, Ex MoD, 109 SOLD
1986 90 2.5D Pick Up - SOLD

Offline 90sam

  • Posts: 265
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Rear Floor
« Reply #5 on: March 28, 2007, 19:13:06 »
The chassis is a galvanised replaced chassis so dont need anything on it for some time!
I was thinking of using some sealent over the top as i plan to carpet/  put rubber on top so would that be okay??
Logged

Offline J.D.

  • Posts: 1002
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • ...Pure as Belfast snow...
  • Referrals: 0
Rear Floor
« Reply #6 on: March 28, 2007, 19:50:16 »
I would think it would be best to have a permenant waterproof surface between the carpet and the holes, otherwise if water does get in, the carpet will soak it up and the rot will spread mate.

You could probably get away with smearing some silicone sealant on some square pieces of 2mm plate steel and pop riveting them down over the holes for a cheap one, or welding for a slightly more expensive one.
Logged
J.D.
- - - -
'ASBO' - Blue Land Rover Recovery Discovery 200TDiS - LR GRAVEYARD OCCUPANT (RIP).
'Green Giant' - Scammel Crusader - WEEKEND WORK!
'Helga' - 2.0T Volvo V40 - BORING!
'Pheonix' - 1995 3.9 V8 Discovery soon to be converted to TDi. - FINISHED!

www.hampshire4x4response.co.uk
www.berkshire4x4response.co.uk

Offline marsie

  • Posts: 301
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Rear Floor
« Reply #7 on: March 28, 2007, 22:35:35 »
Quote from: "Kayaksam"
So it wouldnt fail an mot with it like that?


My 90 hasnt got any rear floor now and passed its test.Took it out and just left the crossmembers for the spare wheel to sit on :wink:
Paul :twisted:
Logged

Offline Nobber

  • Posts: 125
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Rear Floor
« Reply #8 on: March 28, 2007, 22:48:57 »
thats not corrosion between the floor and the chassis , thats corrosion between the floor cross members and the floor plate.i used tread plate on mine but i bolted it through the old floor down onto some new rear floor cross members , you might want to check these for corrosion. best to get it sorted now before it gets any worse , simply hiding it could prove worse in the long run.
to do it properly though it might be a tub off job.
Logged
if it isent broke , whack it with a hammer ,

Offline electricbluebadger

  • Posts: 305
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Rear Floor
« Reply #9 on: March 29, 2007, 17:23:49 »
Quote from: "J.D."
I would think it would be best to have a permenant waterproof surface between the carpet and the holes, otherwise if water does get in, the carpet will soak it up and the rot will spread mate.

You could probably get away with smearing some silicone sealant on some square pieces of 2mm plate steel and pop riveting them down over the holes for a cheap one, or welding for a slightly more expensive one.


To be honest I would pop rivet aluminium plate over an aluminium floor, steel plates will compound the problem in 12 months time, as for welding ... you could if you know anyone with an ACDC TIG who is competent at TIG welding thin alloy but a normal welder wont do the job with aluminium.

Personally Id go for the sheet of chequerplate advice, sealed with silicon...job done

Cheers Steve
Logged
Pages: [1]   Go Up
 





SimplePortal 2.3.5 © 2008-2012, SimplePortal