AuthorTopic: 90 transmision noise  (Read 1214 times)

0 Members and 1 Guest are viewing this topic.

Offline tonycougar

  • Posts: 337
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
90 transmision noise
« on: April 01, 2007, 00:35:53 »
I was dropping some junk off at the tip in my old petrol 90 today and whilst I was driving/coasting between skips noticed a strange knocking noise which I could kind of feel through the clutch pedal, so thought I'd not let clutch out properly, put my foot hard down on clutch pedal but it made no difference.  I was in high first, and it only seemed to happen at those low coasting sort of speeds.
New one to me any ideas :?:
If theres a harder way to do it I`ll find it!!

AbyssDJ

  • Guest
90 transmision noise
« Reply #1 on: April 01, 2007, 00:46:05 »
check UJ's... could be that one or more of them is that knackered that its on the edge of falling apart.

noises and vibrations in landies tend to travel... something that sounds like its in the gearbox can quite often be the rear, etc. irritating!

AbyssDJ

  • Guest
90 transmision noise
« Reply #2 on: April 01, 2007, 00:47:09 »
failing that check halfshafts and drive members for wear. one of our shafts was replaced, and the old shaft now chatters a bit at low speeds when it catches up with the other shaft, if that makes sense?

Offline tonycougar

  • Posts: 337
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
90 transmision noise
« Reply #3 on: April 01, 2007, 00:57:23 »
Quote from: "abyssdj"
failing that check halfshafts and drive members for wear. one of our shafts was replaced, and the old shaft now chatters a bit at low speeds when it catches up with the other shaft, if that makes sense?


It does sound more like something catching up, than a UJ sound (and I've heard enough of them to know em)
If theres a harder way to do it I`ll find it!!

AbyssDJ

  • Guest
90 transmision noise
« Reply #4 on: April 01, 2007, 00:59:06 »
possibly half shafts then. check the rear ones in particular. could just be worn splines like on ours. if it is, its no real problem... just irritating




until it munches the splines off altogether at the lights :P

Offline jimthelandyman

  • Posts: 447
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
90 transmision noise
« Reply #5 on: April 01, 2007, 16:08:12 »
Sounds more like patially siezed thrust bearing catching the diaphram springs on your clutch if you can feel it through your pedal.

Offline tonycougar

  • Posts: 337
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
90 transmision noise
« Reply #6 on: April 01, 2007, 22:25:03 »
hmm possibly, can't recall the exact arrangement of the thrust bearing but makes some sort of sense. I need to try it again I think now I have these ideas in my mind.
cheers guys
If theres a harder way to do it I`ll find it!!

Offline tonycougar

  • Posts: 337
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
90 transmision noise
« Reply #7 on: April 03, 2007, 16:23:55 »
Didn't do it today, maybe I need another run to the tip :lol:
If theres a harder way to do it I`ll find it!!

 






SimplePortal 2.3.5 © 2008-2012, SimplePortal