Pages: [1]   Go Down

AuthorTopic: help!  (Read 1737 times)

0 Members and 1 Guest are viewing this topic.

Offline 90sam

  • Posts: 265
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
help!
« on: April 27, 2007, 22:54:26 »
Would an izuzu 2.8 turbo diesel fit into my 90 N/a diesel and how easy would it be to put in? Wpuld it need any welding and would it match up to the gearbox? Anyone done it before, or have any advice?
Logged

Offline 90sam

  • Posts: 265
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
help!
« Reply #1 on: April 28, 2007, 17:59:23 »
Anyone  :?  If they did then it would be good cause they are fairly cheap and reliable from what ive read. and easy to tune up  :twisted:
Logged

Offline smo

  • Posts: 1381
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
help!
« Reply #2 on: April 28, 2007, 19:01:12 »
Yes it possible, as for further info....youll have to wait until someone who has done it comes along.

Common probs with engine changes are exhause and intake manifolds, engine mounts, gearbox conversion plates to allow mounting and electrics if it has any :)
Logged
'04 90 TD5 - Written off :(

200TDi 90 Hardtop

TD5 North Offroad D-Lander coming soon!!!!

Offline Terranosaurus

  • Posts: 532
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
help!
« Reply #3 on: April 28, 2007, 19:09:23 »
MIght be easier to use the Isuzu gearbox and trandfere too if the outputs are on the right side for a landy. Lot easier to have a couple of custom props made up than to mess about with gearbox adaptor plates and custom clutches etc. Plus the gearing will be matched to the engines characteristics too.
Logged
Nissan 4WD CLUB
Humber and Yorks 4x4 Response
PJ Parts - Motor Trade Workshop Consumables
2000Y 2.7TDi Terrano II
Raising money for Macmillan Cancer Support on the Mac 4x4 Challenge - www.justgiving.com/mac4x4nissan

Offline 90sam

  • Posts: 265
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
help!
« Reply #4 on: April 28, 2007, 20:30:26 »
Hmm thats not really an option! ive seen a couple of conversion kits so i think that shall be the way forward! Anyone got any info on the engine? or how hard it is to fit? Do all the pipes etc match up?
Cheers
Logged

Offline Porny

  • Posts: 1413
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 1
help!
« Reply #5 on: April 28, 2007, 20:35:06 »
I'd get an insurance quote before you fit the engine!!
- some insurance companies don't like non 'Land Rover' engine conversions - especially considering your age...  

And there is the problem that spares won't be avaliable off the shelf...

And your LR will never be worth as much - compared to if you properly fitted a 200 or 300Tdi



Ian
Logged
Buy me another drink - you're still ugly!

Land Rover Diesel Tuning and Diagnostic  http://www.irbdevelopments.com - Mud-Club Member Discount - pm for details!!!

Offline 90sam

  • Posts: 265
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
help!
« Reply #6 on: April 28, 2007, 20:44:41 »
Hmm i shall see what adrian flux have to say! But the parents will be paying for it  :lol:
Yer i gathered parts are expensive but when the enginge are so cheap i could just buy a couple of spare ones!
I'm not really planning on selling my 90 i'd like to take it to uni with me so need something good for distance which is why i've looked into them as i don't really have means of getting the money for a tdi  :cry:  Whereas these give decent fuel and can go 70 easily.
But there appears to be not many conversions into a 90! I found this though..
http://forum.landrovernet.com/showthread.php?t=22507
Logged

Offline Hangover

  • Posts: 267
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: help!
« Reply #7 on: April 28, 2007, 22:07:24 »
Quote from: "90sam"
Would an izuzu 2.8 turbo diesel fit into my 90 N/a diesel and how easy would it be to put in? Wpuld it need any welding and would it match up to the gearbox? Anyone done it before, or have any advice?


My advice is don't bother,i've been down this road,stick another LR engine in and make life simple.
Logged
Pages: [1]   Go Up
 





SimplePortal 2.3.5 © 2008-2012, SimplePortal