AuthorTopic: Attaching Tracmats  (Read 826 times)

0 Members and 1 Guest are viewing this topic.

Offline Jammy123

  • Posts: 3
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Attaching Tracmats
« on: March 20, 2008, 21:47:26 »
This is for my 90 Hard Top.

Im am looking at getting some 50mm thick, 1.5m long tracmats. I only want them for when I go offroad. I am thinking of attaching them to the outside, by drilling 4 holes in the sides of the hard top (at the bottom, near the bar that holds the sides to the vehicle) and then use a 5mm steel spacer plate on the inside with some bolts going through, then put the tracmat waffle over the bolts, then I will use two longs bits of plate to hold the mat inplace, and use wing nuts (for ease of getting off). to secure. Do you think this is a good idea.

I do not want a roof rack as its a daily driver and I dont want to 'damage' my fuel econmy, nor be inconvienced by constantly taking it off or putting it on!

Offline Jimbo

  • Posts: 1126
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Attaching Tracmats
« Reply #1 on: March 20, 2008, 22:24:26 »
Can you not just chuck them in the back of the truck ?
Jim

TDV6 HSE D3
Defender 110 Td5 Hard top, BFG MT's, and no EGR either

http://www.hertfordshire4x4response.net

Offline Jammy123

  • Posts: 3
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Attaching Tracmats
« Reply #2 on: March 20, 2008, 22:26:25 »
I think they will be too long to fit in the load area. There are 1.5m long.

Offline Saffy

  • Posts: 3127
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +1/-0
    • The Bell Inn, Imber.
  • Referrals: 0
Re: Attaching Tracmats
« Reply #3 on: March 20, 2008, 23:01:42 »
I think they will be too long to fit in the load area. There are 1.5m long.

isn't the load area as long(er) as the side panels?  You can shorten em anyway, I reduced  a pair into the tub of my s1, they now live in the footwell of the 2nd row seat in the CSW  Have also seen em fixed directly to the roof too.
« Last Edit: March 20, 2008, 23:03:34 by Saffy »
.swonk eno oN .esoht dna eseht ,siht dna taht ,wollof ot selur emos teg eW

Offline clbarclay

  • Posts: 1615
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Attaching Tracmats
« Reply #4 on: March 21, 2008, 00:11:04 »
If you do go for the bolt and wing nut method then as security drill a hole through the end of the bolt that you can fit a padlock through, preventing the wing nuts from being removed.
Chris

Various range rovers from 1986 to 1988 in various states
Locost sports car based on mk2 escort - currently working on brakes, fuel and wiring

Offline Xtremeteam

  • Regional Rep
  • *
  • Posts: 6476
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Its just the way i roll
    • lampeter, west wales
  • Referrals: 0
Re: Attaching Tracmats
« Reply #5 on: March 21, 2008, 08:27:40 »
or make a pair of book ends & slot them in on the side panel

Mike
I can Drive.. You can criticize..
I too can criticize like you.. but can you Drive like me??


 






SimplePortal 2.3.5 © 2008-2012, SimplePortal