Pages: [1]   Go Down

AuthorTopic: Jimny king pin bearings  (Read 2745 times)

0 Members and 1 Guest are viewing this topic.

Offline kevan1

  • Posts: 21
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Jimny king pin bearings
« on: May 23, 2008, 17:40:25 »
Hi, can anyone tell me, what is the correct  size bearing for the king pins?  Is it possible to get the seals elsewhere as i don't want to pay a fortune at the main stealer's.
Logged
suzuki jimny special, chrome grill trim and chrome washer jets coz the monkeys at longleat chewed them off!

Offline mlines

  • Posts: 74
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Jimny king pin bearings
« Reply #1 on: May 23, 2008, 20:28:35 »
They are Koyo 30302JR (with seal), the other seals you will have to take out and look at the writing on the side as most good bearing suppliers will be able to get them cheaper than the dealer
Logged
Martin Lines
http://www.BigJimny.com

Suzuki Jimny 1.3JLX, Kap 3" Spring Lift, Kap Full External Roll Cage and Front/Rear Bumpers, RockLobster T-Box conversion, ARB Locker, Viair Air System, Recaro Seats

Offline glaggs

  • Posts: 472
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Jimny king pin bearings
« Reply #2 on: May 23, 2008, 21:05:36 »
In my experience the seals don't keep the crap out of the bearings anyway, I've had as much(or little) milage out of King pin bearings witth and without the seal! Just gotta learn to clean em regularly if you drive in mud and water.
Logged
..V..

Offline jamesey

  • Posts: 553
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • land rover recovery service.
  • Referrals: 0
Re: Jimny king pin bearings
« Reply #3 on: May 25, 2008, 18:34:57 »
theres a guy on fleebay selling some , just type in king pin and you shall see , £20 i beleive
Logged

Offline glaggs

  • Posts: 472
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Jimny king pin bearings
« Reply #4 on: May 25, 2008, 18:47:28 »
Got my last set from City seals and bearings - £10+vat each I think.
Logged
..V..

Offline kevan1

  • Posts: 21
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Jimny king pin bearings
« Reply #5 on: May 27, 2008, 10:23:10 »
sorry I meant the big seal at the back on the ball/challace? so 30302 is the size, what does the "JR" stand for in the "30302jr"?
Logged
suzuki jimny special, chrome grill trim and chrome washer jets coz the monkeys at longleat chewed them off!

Offline glaggs

  • Posts: 472
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Jimny king pin bearings
« Reply #6 on: May 27, 2008, 17:53:57 »
JR means its got a seal on it - I think?
Logged
..V..

Offline kevan1

  • Posts: 21
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Jimny king pin bearings
« Reply #7 on: May 30, 2008, 13:06:58 »
OK I have purchased the bearings, gear oil and CV grease. Is there anything nasty I should look out for when changing these bearings?
Logged
suzuki jimny special, chrome grill trim and chrome washer jets coz the monkeys at longleat chewed them off!

Offline glaggs

  • Posts: 472
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Jimny king pin bearings
« Reply #8 on: May 30, 2008, 17:30:58 »
Logged
..V..
Pages: [1]   Go Up
 





SimplePortal 2.3.5 © 2008-2012, SimplePortal