AuthorTopic: snorkel help asap  (Read 1462 times)

0 Members and 1 Guest are viewing this topic.

Offline defender90stan

  • Posts: 56
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
snorkel help asap
« on: October 17, 2008, 20:11:20 »
hi i need a bit of help i am look 4 some flexy pipe the same as what goes from the air box 2 the snorkel but i need it like 2 meters long any 1 no where i can get some of has some  :huh:

Offline MudRat

  • Posts: 1853
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: snorkel help asap
« Reply #1 on: October 17, 2008, 21:41:34 »
any agricultural suppliers should have it

Offline defender90stan

  • Posts: 56
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: snorkel help asap
« Reply #2 on: October 18, 2008, 09:31:36 »
had a look at mole valley but no luck and 1 no any where

Offline zulublue

  • Posts: 756
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: snorkel help asap
« Reply #3 on: October 18, 2008, 12:39:53 »
try giving these a call  www.southdown4x4.co.uk
« Last Edit: October 20, 2008, 22:14:46 by Paul »

Offline TOM TOM GO

  • Posts: 1
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • camel trophy copy 90
  • Referrals: 0
Re: snorkel help asap
« Reply #4 on: October 19, 2008, 09:12:37 »
Hi, I made a snorkel for my 90 a couple of months ago . Very pleased with the result. Went to scrap yard and got some heater vent pipe and used a piece off a ford car, air filter pipe that had a bend in it made in hard plastic and flexy bit at the top to my drain pipe . Bit of a job to get inside vent fitting out from inside of wing but cut with small hacksaw across fitting and pull out. Then I pushed through small gap between wing and heater the flexy heater hose and connected to original flexy tube to filter. Works great and it cost me £5 for bits from scrap yard . Hope this helps you mate..
« Last Edit: October 19, 2008, 09:42:52 by Frankie-Boy »
you think i should use a big hammer on it!

Offline V8burble

  • Posts: 10
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: snorkel help asap
« Reply #5 on: October 20, 2008, 21:20:24 »
Hi, I made a snorkel for my 90 a couple of months ago . Very pleased with the result. Went to scrap yard and got some heater vent pipe and used a piece off a ford car, air filter pipe that had a bend in it made in hard plastic and flexy bit at the top to my drain pipe . Bit of a job to get inside vent fitting out from inside of wing but cut with small hacksaw across fitting and pull out. Then I pushed through small gap between wing and heater the flexy heater hose and connected to original flexy tube to filter. Works great and it cost me £5 for bits from scrap yard . Hope this helps you mate..
Cheapskate :lol:....works though and looks good dunt it Tom :lol:
Thirsty V8 110 named "Trouble"
Frogeyed Sprite in bits
Pug 205 Mi16

Offline billy badger

  • Posts: 35
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: snorkel help asap
« Reply #6 on: October 29, 2008, 19:12:07 »
try auto-performance.co.uk
they stock a wide range of air hose & silicone hoses & fittings. good prices and helpful too

 






SimplePortal 2.3.5 © 2008-2012, SimplePortal