AuthorTopic: body lift question  (Read 686 times)

0 Members and 1 Guest are viewing this topic.

Offline digger

  • Posts: 198
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
body lift question
« on: November 14, 2008, 18:40:00 »
hi how hard is a body lift on my 300tdi 2 door has anyone got any pictures of one being fitted
200tdi disco project
98 2 DOOR 300TDI DISCO  SUZUKI SJ  FORD TRANSIT suzuki vitara trayback disco project

Offline chris9119

  • Posts: 1400
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • The New Big Boy, Gert...
    • Lordswood, Kent
  • Referrals: 0
Re: body lift question
« Reply #1 on: November 14, 2008, 19:42:47 »
Body lift isn't to hard to do.

Get hold of a wizard kit, which I'm sure have the instructions to complete the task.

Chris
Chris
Si hoc adfixum in obice legere potes, et liberaliter educatus et nimis propinquus ades

http://members.mud-club.com/profiles/chris9119/gallery

Mud-Clubbers do it on channel 30






Offline wizard

  • Posts: 1095
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
    • Cardiff. In the land of our fathers, so i am told
  • Referrals: 0
Re: body lift question
« Reply #2 on: November 14, 2008, 19:49:50 »
Ere you go, this is a basic guide i put together.

wizard :twisted:

Installing a Body Lift.

A basic guide for a Land Rover Discovery Tdi


 

A body lift is not as straightforward as it may seem. You need to do a bit more than put in a set of spacers under the body mounts. This is a basic guide to lifting the body on a Discovery and can be use for other lifts as and when required.

The first job you need to do is replace the five flexible rubber brake lines.

There are two on each front wheel and one over the back axle.

If you install a two-inch body lift I would recommend having plus 4 inch extended brake lines fitted.

 

Below is a list of “other” parts required to do the job.

10 body spacers

10 long bolts (3/8 unf x 6 inch long)

4 rear floor support spacers

4 extended body tie rods

2 radiator mounts

2 rear bumper brackets

2 front bumper brackets.

 

A few days before you begin your body lift its advisable to spray the mounting bolts with a good quality penetrating oil.

 

Begin with taking off the bumpers, or just the plastic end caps if you want to lift the bumpers at a later date. Bear in mind that the bumpers are attached to the chassis so once you have lifted the body you will have a 2-inch gap between the body and bumper.

Remove the 4 body tie rods; these attach the seat belts to the chassis.

Slacken off the steering column bolts; don’t remove the bolts, as the splines on the shaft will only need to move about 10mm as the body is lifted.

Undo and remove the 5 body mounting bolts on one side, and remove the nuts on the bolts on the other side (leave the bolts in position)

With the aid of a Hi Lift jack begin to lift the side with the bolts removed. Periodically check that no electrical wires etc are being pulled out of place; also keep an eye on the air filter pipe work as this is mounted on the body. The clutch pipe work will need to be kept in mind as this is also attached to the body. There is enough slack in both of these components so no extra modifications should be required.

 

Once you have gained enough lift you can start putting in the spacers. When one side is complete continue with the other side. Secure all the body mounting bolts once all the spacers are in.

 

The rear floor support spacers bolt onto the brackets on either side of the rear suspension spring, and support the floor !

 

The radiator is chassis mounted so when you have lifted the body fit the two top mounting spacers onto the two pins located on the sides of the radiator.

 

Attach the extended body tie rods.

Check the steering shaft and re tighten the bolts. Lift the bumpers as and when required

Offline digger

  • Posts: 198
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: body lift question
« Reply #3 on: November 14, 2008, 20:57:09 »
can u put a 4 ing body lift on
200tdi disco project
98 2 DOOR 300TDI DISCO  SUZUKI SJ  FORD TRANSIT suzuki vitara trayback disco project

Offline wizard

  • Posts: 1095
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
    • Cardiff. In the land of our fathers, so i am told
  • Referrals: 0
Re: body lift question
« Reply #4 on: November 15, 2008, 16:54:31 »
You can but i wouldnt recoment it.
You will have a lot more things to concider going from 2 inch to 4 inch.

wizard

 






SimplePortal 2.3.5 © 2008-2012, SimplePortal