Topic: daisy 2.0 build (Read 167898 times)

martyn · « **Reply #270 on:** March 05, 2010, 22:47:28 »

Well its obvious to me if you cant go through got to go down call goes out for the paddy skate board and the HILTI dig 2 trenches in the floor axle width apart 10 inches deep remove truck from garage refill trenches wif chipping so you can drive a car in and if you ever have to work on truck again just dig the chippings back out sorted guvnor.
youll be asking me next what a paddy skate board is wont you :-k

william127 · « **Reply #271 on:** March 07, 2010, 03:27:43 »

whats a paddy skate board?

martyn · « **Reply #272 on:** March 08, 2010, 21:08:13 »

large two stroke disc cutter they use them to cut thro tarmacadam, paving slabs etc you have see them at road works or building sites 20 inch diamond encrusted blade goes thro just about any thing in this part of the world they call them paddy skate boards as they are usually used on road works you have to put your foot on them to start it while you pull the startcord and as many of the workers are Irish hence paddy skate board

william127 · « **Reply #273 on:** March 08, 2010, 22:05:55 »

ah im with you, used one a fair few times myself, good name for it :D

martyn · « **Reply #274 on:** March 11, 2010, 13:24:16 »

we seem to have to keep ourselves amused whilst boss is working so here is the next one.
starter for ten no conferring

fetch the hot spanner is the call down here what /who is the hot spanner top tip Halfords do not sell them even in their professional range

weeone · « **Reply #275 on:** March 11, 2010, 16:28:57 »

I refer to the Hot Spanner as the Blue Spanner :lol:

martyn · « **Reply #276 on:** March 17, 2010, 21:37:22 »

well done thats a good one still another ten points going spare what is the ZIP gun then and no its nothing to do with getting a prostitutes jeans off

martyn · « **Reply #277 on:** March 24, 2010, 19:22:00 »

any update boss whats the latest

boss · « **Reply #278 on:** March 24, 2010, 22:02:43 »

yeah, i done stuff. but you carry on with your workshop slang ;)

martyn · « **Reply #279 on:** March 25, 2010, 13:06:45 »

no takers on the zip gun not going to say yet see if someone can sort it out

heres the next one Bucking bar heres the clue its not in halfords and its nothing to do wif a rodoe any takers

martyn · « **Reply #280 on:** March 25, 2010, 13:08:26 »

hurry up boss the troops want updates not me trying to entertain them

boss · « **Reply #281 on:** March 25, 2010, 17:06:42 »

tabs have arrived, working out geometry for a 3link as we speak, also putting in an order for some links this evening, panhard bracket constructed, front axle cleared up rear steer knuckles waiting for me on the shelf, new hubs being made, but my JD2 is 3 weeks away.......

Xtremeteam · « **Reply #282 on:** March 26, 2010, 17:52:16 »

come on chief.......

i/we built this

in under a month

boss · « **Reply #283 on:** March 27, 2010, 08:39:33 »

very nice mike. but you haveto take into account that im a 45 minuite drive away from the disco, im working by my self, im not in a fully prepped workshop and most of the parts i need are not off the shelf parts. so yah progress is slow but i can deal with that if i have a better result at the end.

topless matt · « **Reply #284 on:** March 27, 2010, 19:25:43 »

You tell him boss.
But seriously well done mike

martyn · « **Reply #285 on:** March 29, 2010, 12:38:58 »

well mike it looks awsome really good but just giving us photos is not enough you know we want more what eng ,box etc

if im being super critical the only bit i would change is the rock slider at the aft end i would have bent it to join to the angle tube coming down as i say if i was being super critical it is far better than i have ever owned so dont get cross just an obsevation

boss · « **Reply #286 on:** April 29, 2010, 21:23:55 »

bah! if i could clear all the crap out of this thread i would!

its arrived, had to send £200 to my father in-law because he got stuck in thailand for 10 days so no die....yet. also have to construct a stand for it too

and how i last left the axles.....

mikiep1986 · « **Reply #287 on:** April 30, 2010, 00:43:53 »

ohhhhh nice and shinney :twisted: looking good so far . . . hope the bender all turns out ok and working soon .. good luck dude :clap:

boss · « **Reply #288 on:** April 30, 2010, 18:54:19 »

going to go have a chat with rob on tuesday and pick up my 4wheel steer knuckles :twisted:

martyn · « **Reply #289 on:** June 14, 2010, 17:15:35 »

Boss whats happening dont go cold on us now whats the latest or are you going to finish it and then post the pics

boss · « **Reply #290 on:** June 14, 2010, 18:52:25 »

yah...i stopped bothering on here, lack of input and intrest so i diddnt see the point

rear axle is now done and steerer and ready to bolt on. ordering some pinion conversions at the end of the week(payday :D ) just while he still has some cheap.
and might be picking up my die next week.

martyn · « **Reply #291 on:** June 22, 2010, 22:11:58 »

dont be get down its just that everyone is interested and wants to see it finished but unfortunatly you have time and monetary constraints
we'r impatient thats human nature

auf_wiedersehen_pet · « **Reply #292 on:** June 23, 2010, 18:04:16 »

Quote from: boss on June 14, 2010, 18:52:25

lack of input and intrest

Not from me Boss - can't wait to see it finished.

:clap: :clap:

boss · « **Reply #293 on:** June 23, 2010, 18:26:49 »

tis nice to know chaps
i dont know when ill have any new pics as im busy this weekend. may be able to sort something out though.

does anyone in the norfolk area have an engine hoist i could borrow for the day?

boss · « **Reply #294 on:** July 18, 2010, 21:03:42 »

pictures say a thousand words, but they dont say thankyou toplessmatt as i would have been stuck 8" off the floor still if i diddnt have an engine hoist. top bloke

that came too :D

mikiep1986 · « **Reply #295 on:** July 18, 2010, 21:06:03 »

i like alot . . . . guess what your next job is dude . . . .

MINEEEEEEEE :dance:

martyn · « **Reply #296 on:** August 03, 2010, 12:44:27 »

very nice indeed both car and the tooling good to see you are buying QUALITY that WILL last you years
my dad bought me my socket set on my 18 birthday an ELORA set which was many moons ago now he has unfortunatly passed on but the elora set still goes on used it last sat fitting neighbours tow bar still going strong

keep it up

topless matt · « **Reply #297 on:** August 03, 2010, 17:27:09 »

No worries, glad it could be of use.
Better start trying to sort the forklift axles out now hadnt i :doh:

boss · « **Reply #298 on:** August 03, 2010, 18:21:32 »

snapon were doing a deal with the top box and rollcab, 100 bit service kit and a selection of pliers and sidecutters for 11.50 a week over all in the deal i save

Xtremeteam · « **Reply #299 on:** August 08, 2010, 00:33:34 »

ahem....... bluepoint dont carry the same warrenty as snap-on, they offer 50% of the replacment cost if you upgrade to snap-on

bluepoint is the budget range of snap-on ;)

News:

AuthorTopic: daisy 2.0 build (Read 167898 times)