Pages: [1]   Go Down

AuthorTopic: Fuses, can I change my bulb fuses to blade fuses?  (Read 894 times)

0 Members and 1 Guest are viewing this topic.

Offline benbenukuk

  • Posts: 179
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Fuses, can I change my bulb fuses to blade fuses?
« on: January 25, 2009, 19:52:07 »
Hi, I have a 1987 land rover 90 with bulb fuses, Is there a way I can change them to blade fuses? cheers.  Ben
Logged
1989 3.5 v8 range rover classic with 3.9 efi system, 6'' lift, +5'' dampers, dislocation cones all round, 12500ib T-Max winch, steering guard, custom made rock sliders, light pod, custom made side exit exhaust, welded front and rear diff guards, full roof rack, 35/12.50R15 BFG Muds, CB Radio, Twin Batteries, Rear ARB Locker :)

Offline V8burble

  • Posts: 10
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Fuses, can I change my bulb fuses to blade fuses?
« Reply #1 on: January 25, 2009, 21:09:00 »
Quote from: benbenukuk on January 25, 2009, 19:52:07
Hi, I have a 1987 land rover 90 with bulb fuses, Is there a way I can change them to blade fuses? cheers.  Ben

Get a blade fuse box from Vehicle wiring products
 http://www.vehicle-wiring-products.eu/VWP-onlinestore/fuses/holders1.php
Logged
Thirsty V8 110 named "Trouble"
Frogeyed Sprite in bits
Pug 205 Mi16

Offline fezzy192

  • Posts: 341
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • THERES NOTHING BETTER IN LIFE THAN THE GREEN OVAL
    • birmingham
  • Referrals: 0
Re: Fuses, can I change my bulb fuses to blade fuses?
« Reply #2 on: January 26, 2009, 09:22:51 »
my defender is a 1985 and mine was changed before i brought the car i think 1986 ish range rovers have the same fuse box but blade type hope this helps
Logged

Offline craig_midz

  • Posts: 397
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Fuses, can I change my bulb fuses to blade fuses?
« Reply #3 on: January 26, 2009, 17:29:06 »
yes mate its easy all u got to do is cut the wires one at a time a put a spade connector on it an then get a bladed fuse board from local motor factors 6 bladed one fits in exsistin hole perfectly
Logged

Offline benbenukuk

  • Posts: 179
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Fuses, can I change my bulb fuses to blade fuses?
« Reply #4 on: January 27, 2009, 18:00:04 »
Thanks for the replies, It will be a job in the near future.  Ben
Logged
1989 3.5 v8 range rover classic with 3.9 efi system, 6'' lift, +5'' dampers, dislocation cones all round, 12500ib T-Max winch, steering guard, custom made rock sliders, light pod, custom made side exit exhaust, welded front and rear diff guards, full roof rack, 35/12.50R15 BFG Muds, CB Radio, Twin Batteries, Rear ARB Locker :)
Pages: [1]   Go Up
 





SimplePortal 2.3.5 © 2008-2012, SimplePortal