Pages: [1]   Go Down

AuthorTopic: Doors not aligning  (Read 1171 times)

0 Members and 1 Guest are viewing this topic.

Offline Highland_Defender

  • Posts: 133
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Doors not aligning
« on: February 19, 2009, 21:33:31 »
Ive just changed my doors over from split doors to windups but they wont close because the bottom of the door catches my tree sliders. what would cause that? Ive adjusted the hinges to tilt the door up but its not enough.

Any help greatfully received, Cal
Logged
06 Mitsubishi L200 animal-BFG A/T 265-70-17, Midland cb, twin arials, 4 light force 170 lights (for sale)!! Cheap to a good home

Landrover 3.5v8 90-Tree sliders, steering guard, tank guard, light bar, 8 spokes with xzl's

Yamaha 350 Bigbear 4x4-Front VIPER Elite winch, Rear VIPER Elite demount winch, Warn spot lights, 28" tyres

www.nessoffroad.co.uk

Offline bogie

  • Posts: 695
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • IF IT AINT GOT LEAFS,ITS NO GOOD!!!!!!!!
  • Referrals: 0
Re: Doors not aligning
« Reply #1 on: February 20, 2009, 21:29:26 »
TAKE THE TREE SLIDERS OFF!!!!!!!!!!!!!!!!!!!!!!!!
Logged
1968 SERIES 2A ,200TDI TUNED,RANGE ROVER AXLES,ONE TON SHACKLES,CPC PARAS,ES3000,POLYBUSHED,ANACONDAS.                     1970 SERIES 2A, 200TDI TUNED,5 SPEED LT77 WITH LT230S TRANSFER BOX 1.211 RATIO.ZEUS DISKS ALLROUND.ES3000,MODIFIED 90 TANK,3.5 DIFFS.

Offline Artwigwa

  • Posts: 162
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Doors not aligning
« Reply #2 on: February 21, 2009, 18:34:51 »
Sounds like the door hinges are worn causing the new heavier door to drop. with new hinges there should be no reason for the doors to catch on the sliders  :-k 

Try adjusting the hinges, loosen all four screws on hing, lift door using a jack on handle side, tighten all four screws up then release the jack.  :dance:
Logged

Offline Highland_Defender

  • Posts: 133
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Doors not aligning
« Reply #3 on: February 22, 2009, 20:07:59 »
Well i have fitted new hinges to the doors and adjusted the hinges by slackening them and jacking up the low end of the door gently but it has only resulted in a minor change.  :?

I was thinking my bulkhead might be twisted or the doors are off the square. Away to check right now.
Logged
06 Mitsubishi L200 animal-BFG A/T 265-70-17, Midland cb, twin arials, 4 light force 170 lights (for sale)!! Cheap to a good home

Landrover 3.5v8 90-Tree sliders, steering guard, tank guard, light bar, 8 spokes with xzl's

Yamaha 350 Bigbear 4x4-Front VIPER Elite winch, Rear VIPER Elite demount winch, Warn spot lights, 28" tyres

www.nessoffroad.co.uk

Offline trickydicky

  • Posts: 193
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • took some bits off now its streemline
  • Referrals: 0
Re: Doors not aligning
« Reply #4 on: February 23, 2009, 17:17:50 »
i had a simular problem when i re chassied mine . i found that there is adjusting bolts between the bulkhead and the windscreen the more you tighten them the ferther forward it pulls the top of the bulkhead . do you have the hinged type of windscreen hinges? 
Logged

Offline Highland_Defender

  • Posts: 133
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: Doors not aligning
« Reply #5 on: February 23, 2009, 19:16:58 »
Quote from: trickydicky on February 23, 2009, 17:17:50
i had a similar problem when i re chassied mine . i found that there is adjusting bolts between the bulkhead and the windscreen the more you tighten them the farther forward it pulls the top of the bulkhead . do you have the hinged type of windscreen hinges? 
Yes Ive got a hinged windscreen, where about are these bolts exactly?

I swapped my drivers door again to another i had  and it fits but not perfectly still low, and only just clearing my sliders.
its defiantly my bulkhead.
Logged
06 Mitsubishi L200 animal-BFG A/T 265-70-17, Midland cb, twin arials, 4 light force 170 lights (for sale)!! Cheap to a good home

Landrover 3.5v8 90-Tree sliders, steering guard, tank guard, light bar, 8 spokes with xzl's

Yamaha 350 Bigbear 4x4-Front VIPER Elite winch, Rear VIPER Elite demount winch, Warn spot lights, 28" tyres

www.nessoffroad.co.uk

Offline trickydicky

  • Posts: 193
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • took some bits off now its streemline
  • Referrals: 0
Re: Doors not aligning
« Reply #6 on: February 23, 2009, 19:42:22 »
the bolts are eather side of the windscreen on the bottom as you tighten them the doorsdack corner should start to lift up . its a dead easy job it will only take about 5 mins 8-[
Logged

Offline trickydicky

  • Posts: 193
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • took some bits off now its streemline
  • Referrals: 0
Re: Doors not aligning
« Reply #7 on: February 23, 2009, 19:50:31 »
also try jacking up the back of the doors when ya do it or you have to give them some welly
Logged
Pages: [1]   Go Up
 





SimplePortal 2.3.5 © 2008-2012, SimplePortal