AuthorTopic: 200tdi chassis question??  (Read 1605 times)

0 Members and 1 Guest are viewing this topic.

Offline stretchy

  • Posts: 414
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
200tdi chassis question??
« on: February 12, 2010, 11:58:01 »

hi guys.. ive got a striped down 200tdi chassis ready for a new project. im going to sand it all down and waxoil it. my question is how do i deal with the botem  tow bar brakets. there is the remainder of the bolts still stuck in there and i cant get them out, are they welded ?? I do need the brakets left in tact if this is posible

stretchy
All the Gear, No Idea!

I break land rovers!
07716989933

Offline J.D.

  • Posts: 1002
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • ...Pure as Belfast snow...
  • Referrals: 0
Re: 200tdi chassis question??
« Reply #1 on: February 12, 2010, 13:06:06 »
Drill or punch them out with a big hammer. May need a generous application of heat or WD40!
J.D.
- - - -
'ASBO' - Blue Land Rover Recovery Discovery 200TDiS - LR GRAVEYARD OCCUPANT (RIP).
'Green Giant' - Scammel Crusader - WEEKEND WORK!
'Helga' - 2.0T Volvo V40 - BORING!
'Pheonix' - 1995 3.9 V8 Discovery soon to be converted to TDi. - FINISHED!

www.hampshire4x4response.co.uk
www.berkshire4x4response.co.uk

Offline lee celtic

  • Regional Rep
  • *
  • Posts: 2680
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: 200tdi chassis question??
« Reply #2 on: February 12, 2010, 15:21:15 »
there is a small drain hole in the middle of the tube (on the bottom) make it a little bigger and stick the tube off a wd40 can in there and spray a lot..

then get a junior hacksaw blade cut it to a point at one end so the teeth form a hook and work it down the side of the bolts spraying now and again.. the bolts are thinner than the size of the hole they will be held in by compacted rust and dirt.. It took me 30mins each side to get mine out like this so I could fit a dixon bate to the car..

the garage that was going to do the job were going to drop the tank and burn them out..! :evil: needless to say they won't be touching my car again. ;)
so many hills , so little time ....
discovery TD5
work in progress...lol

Offline stretchy

  • Posts: 414
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: 200tdi chassis question??
« Reply #3 on: February 12, 2010, 15:22:55 »
i have tried the big hammer its just flating the end of the bolt. if i tried drilling i dont think i could keep it straight enough to drill the bolt only and would proberbly mangle the braket. I was thinking of cuting them of then welding some more on but I need it safe to tow ~

thanks

stretchy
All the Gear, No Idea!

I break land rovers!
07716989933

Offline stretchy

  • Posts: 414
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: 200tdi chassis question??
« Reply #4 on: February 12, 2010, 15:29:12 »

I have just pulled a dixon bate of the chassis so may be uprated bolts as they are that tight i dont think its just rust jamming it. running out of options other than to cut them off. can i buy new brackets?? or is a jate ring ideal to use as a tow bar bracket ???


thanks

stretch
All the Gear, No Idea!

I break land rovers!
07716989933

Offline lee celtic

  • Regional Rep
  • *
  • Posts: 2680
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: 200tdi chassis question??
« Reply #5 on: February 12, 2010, 15:33:42 »
jate rings bolt through the same holes I think.. :-k

when they were trying to  do mine they tried cutting the heads off and punching them through but the would not budge ..

trust me it's the cack traped in there jamming them in scrape round the bolts a bit with plenty of WD40 and they will move . it just takes time..
so many hills , so little time ....
discovery TD5
work in progress...lol

 






SimplePortal 2.3.5 © 2008-2012, SimplePortal