Pages: [1]   Go Down

AuthorTopic: rattling noise  (Read 1668 times)

0 Members and 1 Guest are viewing this topic.

Offline Sabo

  • Posts: 70
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
rattling noise
« on: August 28, 2010, 19:48:18 »
Hi

There is a loud rattling noise coming from my bellhousing/gearbox,  it drives fine, just got back from Wales and still OK.
The noise is there sometimes and then goes, first thought it might be the turbo until I got under the car and got the wife to press down the accelarator.
Any ideas, I am going to split the gearbox tomorrow to see unless someone knows different?

Cheers
Dave
200tdi 110
Logged
Sabo

Offline Sabo

  • Posts: 70
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: rattling noise
« Reply #1 on: September 05, 2010, 19:32:16 »
Hi all

Split box from engine, changed clutch bits, cleaned out the gearbox oil!, put new seal and gasket on the gearbox, put back together and gues what - the noise is still there, I now suspect the gearbox so I think it's time to leave and wait till it dies.

Might think of changing to a R380.

Dave
Logged
Sabo

Offline topless matt

  • Posts: 503
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: rattling noise
« Reply #2 on: September 07, 2010, 06:24:03 »
Check the propshaft ujs, they can make a noise coming from that area.
Logged
300tdi, southdown snorkle, tubular bumper, tds winch with dyneema, tree sliders, 6 spotlights, creepy crawler tyres, 2" lift, dislocation cones, dropped mounts all round, wide angle propshafts, mud dash, bucket seats

Likes to eat badgers

Offline Saffy

  • Posts: 3127
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +1/-0
    • The Bell Inn, Imber.
  • Referrals: 0
Re: rattling noise
« Reply #3 on: September 07, 2010, 07:39:23 »
speedo cable rattling on the exhaust, hand brake cable vibrating on the seat box, oil shield on the transfer box output loose and spinning, propshaft UJ's worn.... but I guess you tried all that before diving into gearbox.
Logged
.swonk eno oN .esoht dna eseht ,siht dna taht ,wollof ot selur emos teg eW

Offline bogie

  • Posts: 695
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • IF IT AINT GOT LEAFS,ITS NO GOOD!!!!!!!!
  • Referrals: 0
Re: rattling noise
« Reply #4 on: September 07, 2010, 23:02:50 »
Did you feel any play on the gear box out put shaft????
Logged
1968 SERIES 2A ,200TDI TUNED,RANGE ROVER AXLES,ONE TON SHACKLES,CPC PARAS,ES3000,POLYBUSHED,ANACONDAS.                     1970 SERIES 2A, 200TDI TUNED,5 SPEED LT77 WITH LT230S TRANSFER BOX 1.211 RATIO.ZEUS DISKS ALLROUND.ES3000,MODIFIED 90 TANK,3.5 DIFFS.

Offline Sabo

  • Posts: 70
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: rattling noise
« Reply #5 on: September 10, 2010, 19:21:23 »
Hi guys

I suspect it could be to do with the shimming on the gearbox from cover plate - the one that holds the bearings in place where the pinion shaft goes in.
It's all bolted together now so I'm just going to run it and hope for the best had enough of messing.

cheers
Dave
Logged
Sabo
Pages: [1]   Go Up
 





SimplePortal 2.3.5 © 2008-2012, SimplePortal