Mud-club

Vehicle & Technical => Series Land Rovers => Topic started by: landroverkeith on October 02, 2005, 13:22:35

Title: Series 3 clutch or gearbox problems
Post by: landroverkeith on October 02, 2005, 13:22:35

:?  can anyone offer a suggestion plz, on my series 3 were having problems selecting a gear... when i purchased the car the guy told me it just needed a master clutch cylinder but upon inspection it seems to be working fine same with the slave etc.
At first with the clutch depresed it wouldnt go into gear without the crunchy noises we all hate, then later it went into gear fine but no movement as the clutch pedal was lifted.
Then we found reverse works and almost took out the garage wall  :oops: it drives lovely backward...   :P
id be greatfull of any ideas thanks keith

Title: Series 3 clutch or gearbox problems
Post by: Miniman on October 02, 2005, 21:17:15

I also had the same problem and it came down to the clutch adjustment. There are 2 bolt under the plate in the engine bay and you can adjust the pedal. I know it sounds strange but you can adjust it up so the clutch plate clears more or less. Hard to do as you need think spanners to adjust the bolts. Hope this is your problem. Took me about twenty time to adjust it to get it correct. hope you do it in less time....

If you adjust to much the clutch will slip.
If you adjust it to little it wont clear thus having revers ok but forward gears fine. Put it in gear then start the engine this will let you know if the gears forward are ok.

Title: Series 3 clutch or gearbox problems
Post by: landroverkeith on October 02, 2005, 21:22:22

Thanks for the Tip i was just reading your other post too lol
hopefully my good friend rick if he can pop round weekend  :wink:  if ya reading rick nudge nudge m8  :wink: well try your idea first if car is in gear and i turn the ignition it will roll forward so thats a good sign at least

Title: Series 3 clutch or gearbox problems
Post by: Miniman on October 02, 2005, 21:25:12

Yes good sounds like the clutch is not disengaging ( Clearing ) properly that makes it very hard to get in gear....

Title: Series 3 clutch or gearbox problems
Post by: landroverkeith on October 08, 2005, 16:10:02

:twisted:   ITS ALIVEEEEEEEEEE!!!  :twisted:

Firstly a BIG THANKS to  Rick aka "rickjames" for spending the day with me on the old beast changed the master clutch cylinder and bled the system with me helping where i could, so now i have a driveable series 3 ooo id forgotten how much i like power steering though  :lol:  

And Also thanks to "sarge" for making the trip over to lend me his bleeding kit which we didnt need in the end  :oops:  sorry m8 lol though i did make him a lovley mug of tea :)  

Looking forward to trying out the old gal at tixover  :twisted:

Title: Series 3 clutch or gearbox problems
Post by: Miniman on October 08, 2005, 21:54:05

Nice to know you got it sorted mate. I have just changed the Gearbox today in my series 3 started at nine this morning and finnished at 8.30pm. What a pain in the back side. Found loads of metal bits in oil out of the old one. New one whines in fist second and third but other than that is ok. Will be going green laneing with it on the 23rd October we got a outing organised in the greenlane Forum. Nice to know you got it sorted tho...Have fun...

Title: Series 3 clutch or gearbox problems
Post by: landroverkeith on October 08, 2005, 21:59:39

heheh 23rd of october i should be playing in farley quarry

mind u thats if i can get a trailer cos i aint driving it up that far lol