Mud-club
Vehicle & Technical => Discovery => Topic started by: BigBlue90 on March 30, 2006, 11:58:16
-
Hi, anyone any ideas if replacing a thrust bearing on a 1993 200tdi disco is expensive or time consuming?
-
Hello
Yes the thrust bearings are expensive to replace if you don't do it yourself,
if you are replacing the thrust bearing also replace the arm as well.
You can do both the these jobs by moving the gearbox backwards about six to eight inches and alittle struggling, if the cluth has not been done for a long time have this done at the sametime!!!
Good luck
Nick
-
if your doing the thrust bearing do EVERTHING else inside which is replaceable, it'll save you a lot of time and money in the long run
So thats clutchcover , cover plate, crank shaft oil seal, clutch fork, and depending on its condition, the bracket and pin that the clutch fork sits on
don't forget to get a couple of new plastic clips which hold the push rod into place.
TIP - when your ready to fit the plastic clip, stick it in a mug of hot water for a wee while, far less likely to break.
-
I think I may have the same problem. What sort of cost in parts are to be expected for all that you have listed?
Cheers
-
Brilliant help chaps, might leave it untill the weather gets a bit more sunny and stops raining. It might also give me enough time to work out which is correct end of a spanner!!!!
-
ive just done trhe clutch and bearing on mine the quickest way and easiest is to take the engine out
-
Personally i prefer to take out the gearbox/transfer box complete, a bit heavy but o.k.Not too bad a job but as already has been said best to replace all the bits whilst the box is out.Only takes a couple of hours at most to get the box out, good luck
mate
Neil.....
-
ive just done trhe clutch and bearing on mine the quickest way and easiest is to take the engine out
Quickest and easiest :shock:
-
ive just done trhe clutch and bearing on mine the quickest way and easiest is to take the engine out
want to come and do mine as think its just gone
:cry:
-
ive just done trhe clutch and bearing on mine the quickest way and easiest is to take the engine out
Quickest and easiest :shock:
It is in a series 3 lightweight, Also after this summer my front on the disco is having a removable bonnet slam plate. so it may well be better for me to look at a clutch change that way too, have to think about that though
-
if you lift the engine out that should take about 1 1/2 hours 1 hour to change clutch crank oil seal arm and bearing 1 1/5 job done and then back to play 8) 8)
-
if you lift the engine out that should take about 1 1/2 hours 1 hour to change clutch crank oil seal arm and bearing 1 1/5 job done and then back to play 8) 8)
and if it rains you can always put the bonnet down and work undercover :lol:
-
if you lift the engine out that should take about 1 1/2 hours 1 hour to change clutch crank oil seal arm and bearing 1 1/5 job done and then back to play 8) 8)
and if it rains you can always put the bonnet down and work undercover :lol:
never thort of that :D :D
-
If you don't have a pit or ramps I think it's easier/safer to move the engine too, the box weighs the same anyway and you aren't working beneath it :o
If you are only replacing the clutch then you can perhaps get away with slewing the engine forwards and not lifting it out, but it might be worth a new crank oil seal and check the surface of the flywheel too. If it doesn't come out you only need to split the exhaust, remove the rad etc as the wiring and heater hoses should allow you to move the engine forewards.
If only Rover had had the sense to make an inspection cover you could assemble the clutch loosely and tighten the cover plate after the pilot bearing was in place. I find lining that up the hardest part.