Mud-club
Vehicle & Technical => Discovery => Topic started by: beggers on December 26, 2006, 13:46:50
-
Hi everyone. Does anybody know of anyone who fits the late model TD5 lights to a 300TDi? I know it can be done and can be quite tricky and would have a go myself but have nowhere to do it and use the car everyday so need it doing quickly. Also I suspect my sunroof drain is blocked as it's leeking in in the drivers footwell but I'm a bit apprehensive about taking the headlining out again any help would be appreciated.
-
If you've got more money than sense these people will do it for you, takes 3 days though and while your there ask then to put a rear wing on as well. :shock:
http://www.gdautocosmetics.co.uk/pages/about%204x4.htm
Here's one they did a while back
-
If you've got more money than sense these people will do it for you, takes 3 days though and while your there ask then to put a rear wing on as well. :shock:
http://www.gdautocosmetics.co.uk/pages/about%204x4.htm
[/b][/color]
Just checked out the link I think I will book my 200tdi in for a full makeover - :(kerching): NOT!!
Must say I like the silver Disco front end conversion, Bumber, lights etc
:(stoopid):
-
you can fit the lights to a 300tdi but its not a job for the faint hearted once you cut to fit theres no going back, fingers mclean on here has done it to his and it looks cool but if you speak to him its not a nice job
-
Thanks for the info. Been to the site and it's a bit too pricey for me. I'd heard it was a tricky job. Think I'll have to shelve the idea for now. Thanks all.
-
Why not fit the early Series 2 lights?
They fit straight in without any modification
(http://members.mud-club.com/galleryimages/904dee9add247f656b7d097aeeb88668.jpg)
I have white indicators too
Looks nice i think
8)
-
TOTAL PIG OF A JOB, THE TD5 WINGS ARE DIFFERENT TO THE 300TDI THEY AREWIDER, I HAVE SEEN SEVERAL CRAP CONVERSIONS (INCLUDING THE ONE I DID), BUT HAVE SEEN 1 WHERE IT ACTUALLY LOOKS RIGHT. I WOULD RECCOMEND NOT BOTHERING AS ITS A 99% CHANCE YOURE GONNA BU@@ER YOUR WINGS UP!
IVE NOT LOOKED ON THAT LINK, BUT GET THE IMPRESION ITSA LOT OF LOLLY, THATS BECAUSE ITS A MEGGA JOB, SO DONT BE TO HARD ON THEM.
-
TOTAL PIG OF A JOB, THE TD5 WINGS ARE DIFFERENT TO THE 300TDI THEY AREWIDER, I HAVE SEEN SEVERAL CRAP CONVERSIONS (INCLUDING THE ONE I DID), BUT HAVE SEEN 1 WHERE IT ACTUALLY LOOKS RIGHT. I WOULD RECCOMEND NOT BOTHERING AS ITS A 99% CHANCE YOURE GONNA BU@@ER YOUR WINGS UP!
IVE NOT LOOKED ON THAT LINK, BUT GET THE IMPRESION ITSA LOT OF LOLLY, THATS BECAUSE ITS A MEGGA JOB, SO DONT BE TO HARD ON THEM.
Stop Shouting :!: :!: my head hurts after crimbo :wink:
-
Why not fit the early Series 2 lights?
They fit straight in without any modification
(http://members.mud-club.com/galleryimages/904dee9add247f656b7d097aeeb88668.jpg)
I have white indicators too
Looks nice i think
8)
how long u had the clear indercators jake??
dan
-
Since Abingdon Dan
8)
-
Since Abingdon Dan
8)
oh right i dont member them
-
I have a set of 2003 onwards light units and was thinking of doing this eventually. I was actually thinking of getting hold of a TD5 front wing and seeing if they fit the 300.
I currently have early td5 lights with clear indicators. But then, I am nuts, I also have a 2004 TD5 steeringwheel and airbag and electric folding wing mirrors activated by the mirror switch.
So far its cost a small fortune but I am in love with her !
I want that bonnet scoop !!!! Where did that come from ?!?!?!?!?!
-
It looks like one from a Nissan Pulsar Gti-R to me but probably wrong!
-
petergalileo
The wing on the Td5 disco is longer
You could get hold of one to see the cuts you'd have to make though
Just a thought
:wink:
-
Why not fit the early Series 2 lights?
They fit straight in without any modification
Hmmmm. My DI has headlight levelling (which is adjusted via a switch on the dash) and the headlights have a little ball-joint on the bottom left corner which connects to the actuator. Do early Disco II headlights have this ball-joint too? I'd like to fit DII headlights! :D
--David
-
have a word with barmiebrummie cos he fitted them to a range rover - so should be a similar sort of job