Mud-club
Vehicle & Technical => Discovery => Topic started by: BRO on January 08, 2005, 11:18:45
-
Dealers noted oil leaks at last service...
So did a steam clean. I took irt in yesterday to get them to appraise where the leaks were from...
Rocker cover Gaskets
Valley gasket
Head Gasket
and Sump Gasket! :shock:
Resultant bill iro ~£800-900
Is this possible? - all gone at once?
Anyway AA motosure warranty (£700ish extended from dealer I purchased vehicle from!) doesn't cover external oil leaks... - BUT does cover the Head Gasket! \:D/ This means all the top end has to be dissasembled to get there and therefore they can cover all the top end gaskets! YeeHar! :D
Anyway this leaves the sump gasket to be done - I think he quoted ~£50 ish for gasket and ~ £90 labour - I'm figuring that while they are doing all the rest I might as well have it all sorted! - Also if they spot anything else whilst dissasembling most of the engine they can get that sorted too before the warranty runs out in June...
Any comments/advice?
Cheers
Mick :D
-
50 Quid for a gasket ???!!!
Blimey...
-
Must be made out of 5 pound notes!
Ed
-
:roll: Bah Humbug - might have known I'd get this kind of response here... :wink:
I would have asked on Disco2.com but the forum is down :roll:
Anybody here attempted sump removal on DII????
Cheers
-
have you tried other suppliers such as rimmerbros.co.uk or paddockspares.com or mm-4x4.co.uk
there are quite a few in the mags who sell bits for disco 2's
-
:roll: Bah Humbug - might have known I'd get this kind of response here... :wink:
Sorry... natural reaction !
I would have asked on Disco2.com but the forum is down :roll:
You aren't winning any friends you know !
Anybody here attempted sump removal on DII????
No, but if it's anything like my V8, it's a dozen bolts.
BTW...
http://www.mansfieldmotorsltd.co.uk/shop/en/browse/Discovery+II/13/0/9/31/522/2784
That's a V8 sump gasket I believe... 15 quid.
-
if its same as a200tdi ,its just a case of removing the bolts,[ after youve drained oil] :wink:
-
I suppose we stated the obvious, that you were being ripped off at £50 for a bit of cork.
Sorry
It should be a competent DIYer job following procedure and tightening the bolts back up in the right way and order.
It is possible to twist parts of the sump when replacing it.
Ed
-
If its a V8 it should be a doddle cos i did the big end bearings & main bearings in place on the racer (severe lack of oil pressure) & its easy enough to do in place,if its a td5 I dunno how difficult it is but i will have a look at the 1 at my work on the ramp on wed,
-
Thanks guys...
I've just checked in the RAVE docs and it doesn't seem too difficult at all :D
And £15.50 for the gasket from mansfield... :lol: can't go wrong :wink:
I take it all back - you guys are the greatest 8) Long live Mud-Club :lol:
Cheers
Mick :D
-
:-) No probs Mick,
Would probably be worth getting your VIN and checking the part number with Mansfield to be certain, but from what I can tell, that's the right one.
-
Just been to my local Motor parts supplier... £5.50 + VAT !!! - can this be the right part????
-
Hi
If it is the same as a 300tdi you should use a special sealant to stop any future leaks and this is available from land rover in small tubes at £54-00 per tube :shock: a very special sealant, to do the job correctly it costs ya !!
Regards
Pat
-
Perhaps I'll get it welded all round! - That'll stop any further leaks :wink:
-
Ah well - end of story... I'm a wuss, cold & wet outside, poor light and a thousand other jobs to do around the house and on the cars... 8-[
Land Rover dealers done it! [-o<
Good news! \:D/ only £86 bill to me 8) So either i missunderstood, or they miscalculated the estimate...
Cheers