Mud-club
Vehicle & Technical => Discovery => Topic started by: bambamjj on August 15, 2008, 21:23:04
-
Anyone fitted one, if so you got pickies, please
-
yep had mine 5 years now
-
I used to have the rebel 3 piece alloy oneon my old Disco
(http://www.mud-club.com/galleryimages/520590-1109789524.)
Easy to fit but didn't fit with the winch bumper i brought
So i replaced it with a Southdown one
(http://www.mud-club.com/galleryimages/b965096f37936d953988a942a693bf49.jpg)
I now have a D44 version
(http://inlinethumb37.webshots.com/43172/2764025180102123940S500x500Q85.jpg)
:D
-
Ive fitted one to a friends disco the other week. Its a one peace guard but becuase they have a scorpion winch bumper it didn't fit but after a notch on both side its looking good.
-
ive one with the jacking points and tow points one peice. fits inside of the chassis rails. iff you need a pic let me know...alan
-
I have one taken quite a beating but protected everything :D did need a lot of spacing washers to make it fit though.
(http://i244.photobucket.com/albums/gg40/Greedy_016/Off%20Road/16082008439.jpg)
-
I have one taken quite a beating but protected everything :D did need a lot of spacing washers to make it fit though.
(http://i244.photobucket.com/albums/gg40/Greedy_016/Off%20Road/16082008439.jpg)
ur bumper is bent too what do u do drive it at brick walls?
-
I have one taken quite a beating but protected everything :D did need a lot of spacing washers to make it fit though.
(http://i244.photobucket.com/albums/gg40/Greedy_016/Off%20Road/16082008439.jpg)
ur bumper is bent too what do u do drive it at brick walls?
:lol: my local pay and play site in Rochford essex http://www.4x4er.co.uk/home.html (http://www.4x4er.co.uk/home.html) can be very demanding i bent the bumper on the 1st outing :doh: and have since cut it back by about 6 inches as it was rubbing on the tyres. I normally have muds on there but have taken them off as i needed to get the car as low as possible to work on it .
-
ive jst spent an hour looking at the gallery and all i can find is hundreds of people either rolled stuck or with broken vehicles what an amazing site
-
It is a great site with very friendly marshalls but you cant be afraid of getting damaged because it will happen :lol:
-
i wana go there but i live too far away
-
Hi bambamjj I have had mine for about 3 years now. The only drama is getting the steering bolt out I have attached a photo the red ring is round the bolt i used a hammer to get the bolt out which recked the thread you will need a bolt for the off side so get two one to replace the steering box bolt. Jeff
-
I second the above.......I had to cut the steering bolt off to get my guard on!!
-
Hi bambamjj I have had mine for about 3 years now. The only drama is getting the steering bolt out I have attached a photo the red ring is round the bolt i used a hammer to get the bolt out which recked the thread you will need a bolt for the off side so get two one to replace the steering box bolt. Jeff
bit off topic but what bumper is that?
Cheers,
Nick
-
The bumper came from KTC off-road supplies in Wrexham about 2 and a half years ago. The a bar came attached but I had to get I local bloke to weld bits for the lights. My licence plate covers the hole for the winch.
-
i bought one at the land rover show at billing from rebel 4x4 , got it fitted at home but within less than 24 hours had bent it so it was touching the steering arms ( yes it was bent that bad) there great quality for the cost but could possibly do with a bit more strengthening, im going to weld a bit of angle iron on the back as that shud hopfully make it a lot stronger