Mud-club

Vehicle & Technical => Discovery => Topic started by: craig_midz on February 17, 2009, 21:48:02

Title: heater matrix how hard is it ?
Post by: craig_midz on February 17, 2009, 21:48:02: to replace as mine popped on me goin up the m6 this mornin an wasnt nice havin ya car fill with steam at motorway speeds so had to by pass it for now to get me home but how bad a job is it as im gettin quoted 200 quid plus for labour only :O but never done one myself so dont know whats involved any help would be grateful thanks
Title: Re: heater matrix how hard is it ?
Post by: Mud-muncher1 on February 18, 2009, 08:14:35: It's not really a hard job just abit of a pain as you have to take the whole dash out to get to it, does your truck have air-con or without

Jav
Title: Re: heater matrix how hard is it ?
Post by: crazymac on February 18, 2009, 22:39:24: Yeh, what fruitloop said!!

Its nuts and bolts, keep a track of what comes from where and break it into sections

Centre console out
Steering wheel off
Clocks etc off
Jesus bar off
then start to undo the rest

Not difficult but time consuming

You'll need two people at the last bit to take the dash out as its a bit floppy when loose
Title: Re: heater matrix how hard is it ?
Post by: craig_midz on February 21, 2009, 19:46:24: yes mines got air con an will a td5 dash go in as i was given a td5 dash as mines peelin on the front edge so question is will it fit in its place an will everything line up
Title: Re: heater matrix how hard is it ?
Post by: crazymac on February 21, 2009, 23:00:38: I don't think a Td5 dash will fit, they are very different machines.
Title: Re: heater matrix how hard is it ?
Post by: squaddie_fox on February 24, 2009, 20:33:40: TD5 dash does fit, just needs a bit of persuasion! looks good and fits lovely. :D
Title: Re: heater matrix how hard is it ?
Post by: bilge rat on February 24, 2009, 23:02:47: there is a repair strip for the curly dash . got mine off ebay . about 40 quid iff i remember. sure ive read somewhere about a short cut to do the matrix. think its accesssable from the drivers footwell. bit of cutting might be involved. cant say for sure only done a 200 matrix and there certainly isnt an easy way for them .. alan
Title: Re: heater matrix how hard is it ?
Post by: craig_midz on February 25, 2009, 20:01:08: well i did it me an my m8 did it in a couple of hours was quite suprised how easy it was an was thinkin of buyin one of those kits off ebay but got the td5 dash for free an it is exactly the same as a 300 one all my 300 bits went onto it no probs even the passenger air bag dropped in so anyone with a peelin dash sod the kits off ebay buy a cheap td5 dash an change it which has got me thinkin can i put a td5 heaterbox in to get all the electronic heater dials workin or would that be too much hassle
Title: Re: heater matrix how hard is it ?
Post by: blacknight on March 06, 2009, 12:18:53: Quote from: craig_midz on February 17, 2009, 21:48:02
to replace as mine popped on me goin up the m6 this mornin an wasnt nice havin ya car fill with steam at motorway speeds so had to by pass it for now to get me home but how bad a job is it as im gettin quoted 200 quid plus for labour only :O but never done one myself so dont know whats involved any help would be grateful thanks

I know of someone who in the last few weeks has replaced the heater matrix in my old Disco(300 tdi with aircon) without the dash being taken out!!! Not quite sure what was involved in doing this but thought i would just share this info with you.
Title: Re: heater matrix how hard is it ?
Post by: craig_midz on March 06, 2009, 18:48:49: yep aperently u can cut the water pipes from the heater matrix an remove centre console an slide matrix out an then slide new one in an re join pipe work i removed my dash anyway as i had a td5 dash givin to me as my dash was so did 2 jobs at same time :P
Title: Re: heater matrix how hard is it ?
Post by: Disco-andy on March 06, 2009, 20:04:34: there are a lot of screw holding the matrix in right at the back behind the dash, it would be easier to remove the dash i would think.
Title: Re: heater matrix how hard is it ?
Post by: craig_midz on March 06, 2009, 22:18:25: nope no screws hold matrix in the heater box it just slides in an out
Title: Re: heater matrix how hard is it ?
Post by: Disco-andy on March 10, 2009, 22:16:18: YES, i stand corrected i was thinking about taking the hole box out.