Mud-club
Chat & Social => The Bar - General Chat => Topic started by: turtle on April 27, 2005, 22:00:08
-
A day of the farm with Muddyweb in Pictures, somewhere in buckingham.
See my gallery
http://members.mud-club.com/profiles/turtle/gallery/farm
This summed the day up for me :) (sorry tim couldn't resist)
-
That's about the high point of my week... how scary is that !!??
-
Yet another project Tim???
-
More bits for an existing one
There is an engine in that RR which may, or may not, be going in the 'Tigger Too' project
-
That Looked like hard work. :shock:
Looks like you had a nice sunny day tho. :)
-
Maybe you should have gone for this one :wink:
Noticed that the reg is not long after Tiggers http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&category=29748&item=4546002571&rd=1
-
That's travelled well... the reg is a local one to me.
-
Did you have a little play afterwards. :)
-
Well... depends if you count having to winch out of the little padock because the trailer sank up to its axles !!
-
Jonathan,
Do you think Jason will notice that Tim's gone off with his vehicle :lol: :lol: :lol: :lol:
-
Guy ... :lol: :lol: :lol:
Phil, is it my imagination or has that Rangie got a rear prop missing ?
-
it was a good day and it did look nice wether but we did have some rain which made it hard for tigger to get of of the paddock :D
p.s. tim is your finger ok now :lol: :lol:
-
Phil, is it my imagination or has that Rangie got a rear prop missing ?
That not the only thing that was missing :wink:
-
Tim, I’m intrigued, is that an XLR socket you have on the dash by the heater controls on tiger? What's it for?
Sorry just been nosey.
-
It is :-)
The big rocker switch on the panel next to it is the winch control. The XLR is the connector for the winch remote.
-
Ah... I see. Good idea.
Got tones of those kicking around in my car still, was forever replacing them on our avolites lighting desks and DMX splitters, even some of the noise boy equipment which went down well, a lampy fixing sound equipment :shock:
-
Got tones of those kicking around in my car still, was forever replacing them on our avolites lighting desks and DMX splitters, even
[-X Tut Tut.... USITT DMX512/1990 specifies a 5 pin for DMX ;-)
-
Phil, is it my imagination or has that Rangie got a rear prop missing ?
That not the only thing that was missing :wink:
I know nothing about anythink me. 8)
P.S. did you pick up the prop shaft bolts on the ground underneath?
-
did you pick up the prop shaft bolts on the ground underneath?
They would still be on the ground :?
-
Got tones of those kicking around in my car still, was forever replacing them on our avolites lighting desks and DMX splitters, even
[-X Tut Tut.... USITT DMX512/1990 specifies a 5 pin for DMX ;-)
Sorry my mistake they are 5 pin on the desks and dimmers, Macs are 3pin. We were going down the line of wireless dmx for truss to truss data with a local receiver for each truss when I left.
Kept lifting XLR's from the noise boys workshop just incase I had a use for them.
-
Got tones of those kicking around in my car still, was forever replacing them on our avolites lighting desks and DMX splitters, even
[-X Tut Tut.... USITT DMX512/1990 specifies a 5 pin for DMX ;-)
I assume you used to be a lampy then?
-
You could say that ;-)
I started off Freelance, general production stuff, did a load of FOH sound for a few years then moved across to lighting (gotta go where the work is !)
Settled down at Stagecraft in Salisbury for a few years then went up to Lancelyn (Oxford)... doing rental, sales and installation design at both.
A few years back I got an offer from Zero 88 to go and work for them in technical sales which took me off around the world again and eventually I ended up running the company :-)
Was at Zero until a couple of years back when I decided to have a change in lifestyle.. go back to working for myself and *not* travel all over the world any more :-)
-
could have been worse, you could have deserted to do sound :wink:
"without lights its just radio"
Lancelyn hmm, neaver delt with the oxford branch, we used to hire odds and sods off Bob at the North West branch though.
I was freelance LD for a while then settled down with a small lighting company (L.S.S) befor leaving, moving in to IT and becoming a student. The hours were getting a bit much.