Pages: [1]   Go Down

AuthorTopic: Anybody know the head bolts torque settings  (Read 3058 times)

0 Members and 1 Guest are viewing this topic.

Offline Miniman

  • Posts: 1638
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Anybody know the head bolts torque settings
« on: December 21, 2005, 19:27:39 »
Anybody know the head bolts torque settings for a series 3 2.25L Diesel engine?
Logged
WATER DRAWS LAND ROVERS LIKE IRON FILINGS TO A MAGNET
************************************
110 300tdi Everyday car.
90 200TDI Toy
Series3 90 look alike Project.
Skipton North Yorkshire


D E F R A. Destroying English Farming and Rural Areas.

Offline Sharpshooter

  • Posts: 1484
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Anybody know the head bolts torque settings
« Reply #1 on: December 21, 2005, 20:06:38 »
Usually about 15 ftlb's
then 90 degrees
and another 90 degrees.

But some may say different.
Logged

Offline Andy the Landy

  • Regional Rep
  • *
  • Posts: 1105
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Anybody know the head bolts torque settings
« Reply #2 on: December 21, 2005, 22:44:59 »
90lb.ft for the 1/2in. UNF bolts (head bolts)

18lb.ft for the 5/16in. UNF bolts (rocker shaft)

Make sure the sequence is correct and dont put all the pressure on at once :wink:
Logged

Offline Canada Al

  • Posts: 137
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Anybody know the head bolts torque settings
« Reply #3 on: December 27, 2005, 23:04:37 »
90 ft/lbs for head bolts is spot on by the book ....Al
Logged

Offline James.Harwood

  • Posts: 303
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Anybody know the head bolts torque settings
« Reply #4 on: December 29, 2005, 08:29:22 »
RTFM - don't even think about trying head work without the manual, if you torque up or release the head bolts out of sequence you risk knackering your head.
Logged

Offline Miniman

  • Posts: 1638
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Anybody know the head bolts torque settings
« Reply #5 on: December 29, 2005, 20:17:56 »
Cheers lads. I have done it....
Logged
WATER DRAWS LAND ROVERS LIKE IRON FILINGS TO A MAGNET
************************************
110 300tdi Everyday car.
90 200TDI Toy
Series3 90 look alike Project.
Skipton North Yorkshire


D E F R A. Destroying English Farming and Rural Areas.

Offline Spacemud

  • Posts: 243
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
    • Rhoose
  • Referrals: 0
Anybody know the head bolts torque settings
« Reply #6 on: February 09, 2006, 22:31:47 »
Came across this site today. You can download complete service manuals and there there's a page in the series III manual with every torque setting you could imagine.

http://www.landrover.ee/est/varia/downloads/cars.htm
Logged
Spacemud misses his Land Rovers :o(

Offline H

  • Posts: 292
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Anybody know the head bolts torque settings
« Reply #7 on: February 10, 2006, 07:28:11 »
same as any other landy bolt ..... 2 nods and a grunt!

H
Logged

Offline Spacemud

  • Posts: 243
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
    • Rhoose
  • Referrals: 0
Anybody know the head bolts torque settings
« Reply #8 on: February 10, 2006, 09:06:24 »
True, I keep thinking a torque wrench may come in handy oneday though!
Logged
Spacemud misses his Land Rovers :o(

Offline H

  • Posts: 292
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Anybody know the head bolts torque settings
« Reply #9 on: February 10, 2006, 09:17:13 »
I've got one, makes a cracking hammer! ;) I'd personaly be more concerned about the tightening order than the torque settings Chris.

H
Logged
Pages: [1]   Go Up
 





SimplePortal 2.3.5 © 2008-2012, SimplePortal