Pages: [1]   Go Down

AuthorTopic: defender bumpers  (Read 1213 times)

0 Members and 1 Guest are viewing this topic.

Offline gecko

  • Posts: 453
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
defender bumpers
« on: March 11, 2006, 11:02:25 »
ok you lot i dont know if its just me but i have had a night mare refitting my bumper seems to be them clets (the captive thing) so anyone know how to do it esey  ?????
Logged

Offline hobbit

  • Posts: 4750
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
defender bumpers
« Reply #1 on: March 11, 2006, 12:19:32 »
give them a full spray and make sure the bolts are screwing in ok
Logged
Kev

'91 stretch Discovery 200 Tdi
Hybrid for running round (got to go now)
Srs 3 Lightweight petrol (got to go)
Srs 3 Lightweight petrol, runabout

Not every problem can be solved with duct tape, and it's exactly for those situations we have WD 40

littlepow

  • Guest
defender bumpers
« Reply #2 on: March 11, 2006, 17:06:51 »
If your on about the loose metal plates, then get them even from either side, then hold them about 5 - 7mm from the back. Should line up no problems.

 :)
Logged

defenderdan

  • Guest
defender bumpers
« Reply #3 on: March 11, 2006, 17:27:50 »
There are two different types of bolt available. One is a standard bolt which is a pig to get centered when trying to start the thread. The other has a small taper right on the end which sorts that problem for you. I always shove a screwdriver inbetween the bumper and the jacking point too, this stops the plate from flexing down in it's cage whilst starting the thread.
Logged

Offline Bob696

  • Posts: 1697
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
defender bumpers
« Reply #4 on: March 11, 2006, 19:39:38 »
Hammer and lots of swearing.

If that dosnt work then get a bigger hammer. If that dosnt work at least you will feel a lot less stressed out  :twisted:
Logged
"A wise man has something to say a fool has to say something"
"Think of it as evolution in action" and yes, I do know that I can't spell thank you.
200TDi 90  "Daisy" A.K.A. "Baby"
3.5L V8 110 "Sally". The camper van with an attitude problem.

LABOUR
Lying Arrogant Blair Oppressors of UK Rights

Offline mud-club-matty

  • Posts: 1435
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
defender bumpers
« Reply #5 on: March 11, 2006, 19:50:34 »
lots of matinance spray and a hammer
Logged
http://z4.invisionfree.com/4wd_crazy  join me here
www.mm4x4.co.uk www.landymad.piczo.com (my site)
www.scorpionracing.co.uk
www.forest4wd.co.uk (come and have your offroad lessons  here)


  1992 defender 90 200tdi (mine)
 dads work  discovery 300tdi (noppy) co driver
 project discovery 300tdi     (mr p)  project supervisor

Offline Porny

  • Posts: 1413
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 1
defender bumpers
« Reply #6 on: March 13, 2006, 12:38:21 »
Or cut the jacking points off your chassis....

This means you can use a nut and bolt to fit the bumper... as you'll now be able to get to the bottom of the bolt.

Also give a slighty improved approach angle


Ian
Logged
Buy me another drink - you're still ugly!

Land Rover Diesel Tuning and Diagnostic  http://www.irbdevelopments.com - Mud-Club Member Discount - pm for details!!!

Offline gecko

  • Posts: 453
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
defender bumpers
« Reply #7 on: March 13, 2006, 14:42:41 »
Quote from: "Porny"
Or cut the jacking points off your chassis....

This means you can use a nut and bolt to fit the bumper... as you'll now be able to get to the bottom of the bolt.

Also give a slighty improved approach angle


Ian




good thinking that man i have the jacking ponts in the bumper
Logged
Pages: [1]   Go Up
 





SimplePortal 2.3.5 © 2008-2012, SimplePortal