Pages: [1]   Go Down

AuthorTopic: Wiring LPG on a Flapper EFI system  (Read 1716 times)

0 Members and 1 Guest are viewing this topic.

Offline Greybeard

  • Posts: 76
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 1
Wiring LPG on a Flapper EFI system
« on: May 27, 2006, 15:11:21 »
Please can someone tell me which wires i need to cut into on a 1989 3.5 efi with flapper injection system. The Haynes manual is wrong and i have checked 3 of them , the wires are located in the drivers footwell. On my 3.9 with hot wire they are the correct yellow colour, on this 3.5 the wires are a completelu different colour.


HELP !!!!!!!!!!   :(  :(  :(  :(


Steve

Sorry it doesnt explain very well does it, the wires i need are the injector cut wires.   :oops:  :oops:  :oops:  :oops:  :oops:  :oops:
Logged
1999 Disco V8i  mmmmm  nice. LPG Conv.
1990 3.9i Vogue SE offroader.
2" suspension lift including Shock mounts.
OMVL LPG Kit, 10 Bolt Heads, 2" Body lift.
265 x 85 x 16 Grizzly Claws. MPS 4x4 Steering Guard.
SuperWinch EPi9, First 4x4 Winchbumper.
Braided brake lines. Sraight Thru pipe instead of back box for that delicious noise , mmmmm !!!!

Offline Range Rover Blues

  • Moderator
  • ***
  • Posts: 15218
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +3/-0
    • South Yorkshire
  • Referrals: 0
Wiring LPG on a Flapper EFI system
« Reply #1 on: May 31, 2006, 12:29:42 »
Is this sothat the LPG can cut the injectors off? if so my system is installed next to the injector relay (again on a hot-wire).

Have you tried following the pin-out from the ECU?
Logged
Blue,  1988  Range Rover 3.5 EFi with plenty of toys bolted on
Chuggaboom, 1995 Range Rover Classic
1995 Range Rover Classic Vogue LSE with 5 big sticks of Blackpool rock under the bonnet.

Offline Greybeard

  • Posts: 76
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 1
Wiring LPG on a Flapper EFI system
« Reply #2 on: May 31, 2006, 12:43:42 »
It is the injector cut out yes. This is where i have the problem as i do not have a wiring diagram showing the correct info. It is on a Flapper system not hotwire.
Logged
1999 Disco V8i  mmmmm  nice. LPG Conv.
1990 3.9i Vogue SE offroader.
2" suspension lift including Shock mounts.
OMVL LPG Kit, 10 Bolt Heads, 2" Body lift.
265 x 85 x 16 Grizzly Claws. MPS 4x4 Steering Guard.
SuperWinch EPi9, First 4x4 Winchbumper.
Braided brake lines. Sraight Thru pipe instead of back box for that delicious noise , mmmmm !!!!

Offline jjsaul

  • Posts: 1534
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
    • Leeds, West Yorks
  • Referrals: 0
Wiring LPG on a Flapper EFI system
« Reply #3 on: June 15, 2006, 21:48:36 »
we tried to do this on my RRC (1986 flapper)

gave up in the end and took it to a specialist  :roll:
Logged
James

...lovin dirty days out...

1983 OneTen V8 Station Wagon 3.5 (LPG)
1972 Range Rover V8
1992 Range Rover 4.6 (LPG)
1978 Range Rover Carmichael Commando 6x4
1972 Range Rover - Major project, FOR SALE
1976 Range Rover - Less of a project, FOR SALE
Previously: Range Rovers 1988, 1990 and others...
2005 Volvo V70 T5 SE (LPG) - daily driver

Snake110

  • Guest
Wiring LPG on a Flapper EFI system
« Reply #4 on: June 17, 2006, 01:59:15 »
AFIK you can cut the brown wire with orange tracer off the main
relay under youre seat to isolate the injectors
pop a relay in there so on switching the relay
you cut off the injectors but use the same
feed to open the gas solenoyds
this allows the ecu/fuel pump to remain active
thus keeping a supply of fuel circulating
round the injectors thus keeping em cool.
Logged
Pages: [1]   Go Up
 





SimplePortal 2.3.5 © 2008-2012, SimplePortal