Pages: [1]   Go Down

AuthorTopic: what happens when you alter your own prop shafts?  (Read 663 times)

0 Members and 1 Guest are viewing this topic.

Offline mark.yellow.series.3

  • Posts: 1357
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
what happens when you alter your own prop shafts?
« on: July 07, 2006, 19:38:17 »
well ill tell you,
















they bloody fall off. with some nasty noises and bits over the road. :cry:  :cry:  :cry:


so does any one know of a company that make custom length props.

not in the mud yet.
Logged

Offline paul_humphreys

  • Posts: 2181
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
what happens when you alter your own prop shafts?
« Reply #1 on: July 07, 2006, 20:07:22 »
www.gwynlewis4x4.co.uk or theres one called The propshaft clinic, no www for it sorry.

Paul
Logged
LC 80 series 1993. 285/75/16s Cooper STTs, OME 850s on the front with 25mm packer, 868s on the rear. 4.88 diffs. Winch bumper with 12000lb winch. Factory lockers. HD rear bumper with wheel carrier and winch mount.

http://www.crag-uk.org

Offline rollazuki

  • Posts: 869
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
what happens when you alter your own prop shafts?
« Reply #2 on: July 07, 2006, 20:09:05 »
Ive fabbed 2 props, got the rear spot on(local prop balancing company said it didnt need any work(no bill at all, I was pleased)
My tried and tested method is to tag it in place with a couple of small welds, car on axle stands, fit prop.
Mark a white line along the prop, and set the car running in 1st gear.
Watch the prop. as it spins, watch if it goes out of true. Use the line you marked to guage the position.
Next time around, tap the high point with a hammer.....
Continue.......
When theres no discernible runout, carefully unbolt it and add small tacks round the joint before finally welding it up. Preferrably in 1 continuous bead...
The only thing I bust is UJ spiders cos it all runs at daft angles on full droop.

Dont give up, it can be done. Make sure as well that the join has a good groove to weld into, so the bead doesnt just sit on the surface.

As far a prop shops, I can recommend Propshaft Technology in Rotherham, South Yorks.

Good guys, know all about 4x4 and race car/stock car props as well(eh Bulli)

Rolla
Logged
Go on....cut me in half........it says SUZUKI all the way thru the middle!!


Offline mark.yellow.series.3

  • Posts: 1357
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
what happens when you alter your own prop shafts?
« Reply #3 on: July 07, 2006, 21:17:23 »
thanks for that, i dont think it is entirly the props fault, but i do need some proper ones.
  i will give them a call tomorrow.
Logged

Offline blackbob

  • Posts: 1264
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
what happens when you alter your own prop shafts?
« Reply #4 on: July 07, 2006, 21:35:56 »
OH the joys of building landrovers :D
Logged
love's mud and lpg and the wife
skype ekken3011

Offline mark.yellow.series.3

  • Posts: 1357
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
what happens when you alter your own prop shafts?
« Reply #5 on: July 07, 2006, 22:06:04 »
Quote from: "blackbob"
OH the joys of building landrovers :D


yer, no s**t :lol:  :lol:  :lol:
Logged

Offline hobbit

  • Posts: 4750
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
what happens when you alter your own prop shafts?
« Reply #6 on: July 09, 2006, 11:10:16 »
There is a place that specialises in prop shafts here in nottingham, near J26 M1 side
Logged
Kev

'91 stretch Discovery 200 Tdi
Hybrid for running round (got to go now)
Srs 3 Lightweight petrol (got to go)
Srs 3 Lightweight petrol, runabout

Not every problem can be solved with duct tape, and it's exactly for those situations we have WD 40

Offline mark.yellow.series.3

  • Posts: 1357
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
what happens when you alter your own prop shafts?
« Reply #7 on: July 09, 2006, 12:18:05 »
thanks for the replies people.

i will put new spiders and needles in my and run it again, and see what happens.

any tips on reconning the UJ's on props?
 thanks in advance

mark.
Logged

Offline Bulli

  • Posts: 1694
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
what happens when you alter your own prop shafts?
« Reply #8 on: July 09, 2006, 15:19:59 »
Andy can make up some big angle(35 not poxy 30) i'd give propshaft technology a buzz as Rolla said they are really helpful and approachable.
Logged
EFILNIKCUFECIN
Disco V8 3 dr - THROW ME A FRICKIN' BONE HERE.
3 link, lockers and 35's- NUFF said

Offline mark.yellow.series.3

  • Posts: 1357
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
what happens when you alter your own prop shafts?
« Reply #9 on: July 09, 2006, 17:53:51 »
ive got there number, and will get them to price up a pair tomorrow.
Logged
Pages: [1]   Go Up
 





SimplePortal 2.3.5 © 2008-2012, SimplePortal