AuthorTopic: Lifting  (Read 1241 times)

0 Members and 2 Guests are viewing this topic.

Offline ed209

  • Posts: 120
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Lifting
« on: September 08, 2006, 18:41:55 »
I have recently bought a 1986 Rangey Classic, she's mainly standard except for a 6 pot Nissan diesel that runs sweet.
I would like to lift the vehicle a minimum of 2".
What will i need to do this and what are the good and bad points of going higher than 2" say 3 or 4?
'67 Series
SWB SW  
2.25 Derv
Parabolics Extended Shackles
Extended Shocks
RRC Diffs
750 x 16's
Roof Rack / Ladder
Bull Bar (Front) + Spots
14" Mountney steering wheel
Centre Cubby Box
Genuine L/R Oil Bath Air Filter for Snorkel
Snorkel  
65amp 110 Alternator  
*Staffie co driver (never complains and hates horses)*

'63 Series
SWB (open top)
2.25 Petrol (for now)
Rear Mount Tank

Offline barmiebrumie

  • Posts: 1745
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
    • Birmingham, M6 J7
  • Referrals: 0
Lifting
« Reply #1 on: September 08, 2006, 21:14:22 »
For a 2 lift you jusy need 2''+ spring's & shock's, but I would advise putting 2''= extended brake hoses as well,

If you go the 4'' route you will have to modify your prop's & radius arm's (lots of money)

Hope that help's



John.
John.

Offline clbarclay

  • Posts: 1615
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Lifting
« Reply #2 on: September 08, 2006, 21:31:21 »
What reason(s) are you doing the lift for?

2" lift is about the economic limit, beyond this and the costs can start to spiral if you want to do the job properly.

If your after fitting bigger tyres then one option to consider is to lift the suspension 2" and then lift the body if needed.
Chris

Various range rovers from 1986 to 1988 in various states
Locost sports car based on mk2 escort - currently working on brakes, fuel and wiring

Offline Budgie

  • Regional Rep
  • *
  • Posts: 2217
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • This post is best viewed on a computer.
    • Lochaber
  • Referrals: 0
Lifting
« Reply #3 on: September 09, 2006, 00:00:52 »
A standard +2" lift kit may not be enough for you. You'll need to look at the weight of the Nissan engine compared to the standard LR fitment as you may need higher rated front springs to stop it drooping!

The higher you go on the suspension then more it throws out the caster angle on the steering. This makes the vehicle wonder, following any lines in the road you have to keep correcting the steering wheel to keep it in a straight line.
It also changes the angle of the propshaft U/Js and can set up a vibration in the front propshaft.

You may also find that after the lift you will quickly go through propshaft U/Js, suspension bushes and steering balljoints as the lift changes the angles that these parts are used to operating at.

If you're looking at larger tyres then above about 32" dia the gearing starts to suffer and you will be changing down on hills that you happly go up in top at the moment. At lower speeds, 30 or 40 mph, you find your in a lower gear than you are now.

Offline Range Rover Blues

  • Moderator
  • ***
  • Posts: 15218
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +3/-0
    • South Yorkshire
  • Referrals: 0
Lifting
« Reply #4 on: September 10, 2006, 21:25:50 »
I have to echo that, to get Blue running and driving properly I recon that springs and shocks are about half the cost of the job.  Having driven before and after, castor correction just makes it so much better on the road.  I now have to do RRR for my sister as that is also a pig, especialy with the 'van on the back, absolutely no feeling in the steering and only just self-centres.  When I fix the steering box and/or put any new parts in it I expect that to stop altogether, blue did and it was terrible then.
Blue,  1988  Range Rover 3.5 EFi with plenty of toys bolted on
Chuggaboom, 1995 Range Rover Classic
1995 Range Rover Classic Vogue LSE with 5 big sticks of Blackpool rock under the bonnet.

Offline jjsaul

  • Posts: 1534
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
    • Leeds, West Yorks
  • Referrals: 0
Lifting
« Reply #5 on: September 14, 2006, 01:44:51 »
Quote from: "clbarclay"


If your after fitting bigger tyres then one option to consider is to lift the suspension 2" and then lift the body if needed.


Thats what im doing with my project RRC
James

...lovin dirty days out...

1983 OneTen V8 Station Wagon 3.5 (LPG)
1972 Range Rover V8
1992 Range Rover 4.6 (LPG)
1978 Range Rover Carmichael Commando 6x4
1972 Range Rover - Major project, FOR SALE
1976 Range Rover - Less of a project, FOR SALE
Previously: Range Rovers 1988, 1990 and others...
2005 Volvo V70 T5 SE (LPG) - daily driver


Offline simdeb

  • Posts: 624
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Lifting
« Reply #6 on: September 14, 2006, 17:15:36 »
we have a 'L' reg disco and  a 'J' reg rrc. simon took the springs shockers tyres off the disco and put them on the rrc. the rangie drives perfect on them  
but the disco drove very different not for the better. with the tyres it lifted the rrc by about 4'' (my mum has a caravan step to get in and now shes put a piece of string on it so she can pull it up ) bless her!!  

on the disco it changed the speddo by a lot but on the rangie it has not altered at all!
North Nottinghamshire rep for GLASS

nottinghamshirenorth.rep@glass-uk.org

 






SimplePortal 2.3.5 © 2008-2012, SimplePortal