Pages: [1]   Go Down

AuthorTopic: Deep Dish Alloys  (Read 996 times)

0 Members and 1 Guest are viewing this topic.

Offline Litch

  • Posts: 324
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Deep Dish Alloys
« on: October 09, 2006, 20:20:15 »
I was in Rogers of Bedford today and they had a brand new set of Britpart Deep Dish alloys sitting there looking very pretty.

Now I am just about to go out and get myself a set of five Firestyle alloys as I thought these were the only wheels that would fit my 90 while retaining a centre cap (Disco rear axle with 2-piece half-shafts & plastic end-cap) but both Alan in the spares dept and the salesman swore that the Deep Dish alloys also would fit my vehicle with OE (flush) caps as the centre of the wheel is deeper than the OE wheels.
This is at odds with what other wheel suppliers are stating, they all agree that my set-up can only be used with the extended caps available for Firestyles.

If the Deep Dish wheels fit then I will go for a set of them, anyone got them on a similar set-up? I am sure they will let me slip a new rim over my hub if I remove the wheel but I was just wondering if anyone had a definitive answer before I do that?
Logged
ONE LIFE, GET IT!

defenderdan

  • Guest
Deep Dish Alloys
« Reply #1 on: October 09, 2006, 20:24:31 »
If they really want the sale then get them to put one on an prove it :wink:
Logged

Offline Litch

  • Posts: 324
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Deep Dish Alloys
« Reply #2 on: October 09, 2006, 20:33:20 »
Actually they weren't selling, I was buying.

I am sure they would be willing to try it out but they seem pretty positive and there is always the problem that however careful you are, sliding even a bare rim over the studs is sure to leave a few marks on the new wheel. Having said that, if it fits ok I will be buying a set so they won't have lost out and if they don't, everyone will know for the next time. :lol:
Logged
ONE LIFE, GET IT!

Offline M19 ROO

  • Posts: 178
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Deep Dish Alloys
« Reply #3 on: October 10, 2006, 01:44:35 »
get some pics so we can all have a look and either agree how nice they are or slander your good name for such a horrid set of rims  :P  

cheers Ric
Logged

Offline Range Rover Blues

  • Moderator
  • ***
  • Posts: 15218
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +3/-0
    • South Yorkshire
  • Referrals: 0
Deep Dish Alloys
« Reply #4 on: October 10, 2006, 02:13:26 »
I had a problem when I tried to fit 200TDi def internals into the RRC, all was good until I came to fit the alloys, the centres stick though too far plus you need to cjheck you have the correct hubs for Land Rover alloys.  If you have them chances are all will fit, if you don't then centre caps are the least of your worries.
Logged
Blue,  1988  Range Rover 3.5 EFi with plenty of toys bolted on
Chuggaboom, 1995 Range Rover Classic
1995 Range Rover Classic Vogue LSE with 5 big sticks of Blackpool rock under the bonnet.

Offline Litch

  • Posts: 324
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Deep Dish Alloys
« Reply #5 on: October 10, 2006, 19:20:54 »
Went over there today with the intention of slipping a rim over my hub but when I turned up there was already a 90 there with similar spec hubs wearing the same wheels and sure enough, the hub-cap was sitting proud of the wheel meaning the centre-cap could not be fitted. The chap from the parts dept wasn't around but after all his assurances that the centre-cap could be fitted he would have been pretty red faced!
Oh well, back to Firestyles with the extended centre-cap.


Actually the centre caps were my only concern.
I knew the wheels would fit but if I'm spending £600 on new wheels I wanted the centre-cap as well otherwise they just look pants.
Logged
ONE LIFE, GET IT!
Pages: [1]   Go Up
 





SimplePortal 2.3.5 © 2008-2012, SimplePortal