Pages: [1]   Go Down

AuthorTopic: Bulkhead  (Read 832 times)

0 Members and 1 Guest are viewing this topic.

Offline tonycougar

  • Posts: 337
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Bulkhead
« on: June 02, 2007, 00:37:49 »
I have heard that sometimes the MOT testers fail Landys for rusty bulkheads.
Are they right to fail them?
What is the reason for failure? Structural weakness or sharp bits sticking out ie danger to public?
Logged
If theres a harder way to do it I`ll find it!!

Offline Tinks

  • Posts: 119
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Bulkhead
« Reply #1 on: June 03, 2007, 19:00:24 »
Any rust within 30cm of any saftey feature or that causes structual weekness will fail an MOT, so it all depends were the rust is exactly & of course how bad it is.
Although something that is a danger to the public will cause a fail its not a very common reason for failures.

 :wink:
Logged
THE BRIGHTER THE BETTER!

Offline tonycougar

  • Posts: 337
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Bulkhead
« Reply #2 on: June 03, 2007, 22:15:34 »
I have a few spots in the usual place ie Top corners, and a bit under the windscreen.
Logged
If theres a harder way to do it I`ll find it!!

Offline tonycougar

  • Posts: 337
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Bulkhead
« Reply #3 on: June 05, 2007, 23:13:51 »
Anybody know if they would be OK. Could I just fill them for cosmetic reasons or not?
Logged
If theres a harder way to do it I`ll find it!!

Offline Les Henson

  • Posts: 369
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Is it supposed to do that?
  • Referrals: 0
Bulkhead
« Reply #4 on: June 06, 2007, 08:42:25 »
If it's an MOT fail due to corrosion within 30cm of body mount, door hinge, or other stress point then it must be welded. Some rusty holes fail just because they have sharp edges and this type can be filled or even just covered with tape to prevent damage to other persons.


Les.
Logged

Offline tonycougar

  • Posts: 337
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Bulkhead
« Reply #5 on: June 06, 2007, 22:26:32 »
Its not failed, but its due test soon. Is it the proximity to the door hinge that causes failure on the bulkhead?
Logged
If theres a harder way to do it I`ll find it!!

Offline mark.yellow.series.3

  • Posts: 1357
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Bulkhead
« Reply #6 on: June 06, 2007, 22:33:22 »
Quote from: "tonycougar"
Its not failed, but its due test soon. Is it the proximity to the door hinge that causes failure on the bulkhead?


take it along to an MOT man and ask him :D
Logged

Offline tonycougar

  • Posts: 337
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Bulkhead
« Reply #7 on: June 07, 2007, 22:51:44 »
Its due soon so I'll just see if it passes or not.
Logged
If theres a harder way to do it I`ll find it!!
Pages: [1]   Go Up
 





SimplePortal 2.3.5 © 2008-2012, SimplePortal