Pages: [1]   Go Down

AuthorTopic: Rear prop shaft?  (Read 926 times)

0 Members and 2 Guests are viewing this topic.

Offline skiprat

  • Posts: 64
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Rear prop shaft?
« on: July 07, 2007, 19:27:14 »
Hi,

Im not sure if this has been covered, but i couldnt find anything in the search.

My rubber uj type thingy is looking like it could go at any time. so rather than replace it i was wandering if i could fit a rear prop from a 200tdi instead? would it be a straight swap or is there some fettling involved?

many thanks

Kris
Logged
dirt+water= MUD :-)

www.slroc.com

Offline Disco-Ron

  • Posts: 1048
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Rear prop shaft?
« Reply #1 on: July 07, 2007, 20:11:54 »
The 200 prop has a 4 bolt fixing on the rear, where-as the rubber thing i believe has a 3 bolts fixing, i'm not sure if the flange on the diff is interchangable, i'm sure somone out there will know though!!
Logged
gone from 200tdi.... to 300tdi... still with loads done to it, in fact, even more than the last truck...LOL!!!

Offline BtB

  • Posts: 26
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Rear prop shaft?
« Reply #2 on: July 07, 2007, 21:11:25 »
The Rear diff flange needs to be changed for the 4 bolt version. I don't know about the 200tdi propshaft (as i fiited an aftermarket prop)

I have done this and fitted a wide angle prop
Logged

Offline Jake

  • Regional Rep
  • *
  • Posts: 5474
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • <insert witty comment here>
    • South Molton, Devon. UK
  • Referrals: 0
Rear prop shaft?
« Reply #3 on: July 07, 2007, 21:47:33 »
Why dont you just buy a new prop doughnut?
They arn't that expensive
 :D
Logged
Jake

Owner - Land Rover Discovery 2
Driver - Land Rover Defender 100" Trayback

Offline Dr Neil

  • Posts: 818
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +1/-0
  • Referrals: 0
Rear prop shaft?
« Reply #4 on: July 07, 2007, 22:19:28 »
Yes mate all you need to do is get a 4 bolt flange and it will bolt straight onto your diff.The only problem you may have is removing the origonal flange if you don't have access to the special puller.


hope this helps

Neil...
Logged
200tdi over 200kmiles
+2"lift.
Procomp Es9000 shocks
235 MT's on silver modulars
diff guards
tank guard
Paidia4x4 winch bumper.
Discoparts HD rear bumper.
Champion 10000N winch
CB and CDplayer
Safari snorkel
modified turbo actuator vac pipe pick up.
twin batteries with Paidia4x4 split charge system
roof lightbar

Offline Disco_Stu

  • Posts: 402
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Any chance of a tow...?
  • Referrals: 0
Rear prop shaft?
« Reply #5 on: July 07, 2007, 23:02:52 »
The proper UJ from the 200tdi is a better bit of kit IMHO than the Rotoflex coupling on the 300tdi.

I have just changed mine when I did an axle swap. I have definitely seen a thread with pictures of the job being done and instructions on making a puller.

Suggest doing a search for diff flange or similar.

Stu.
Logged
1994 300Tdi Disco    


Snorkel now complete.... http://forum.difflock.com/viewtopic.php?t=1906&highlight=


Offline skiprat

  • Posts: 64
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Rear prop shaft?
« Reply #6 on: July 08, 2007, 19:06:31 »
hi guys,

thanks for your replys, i think that modification might have to wait a while.

so a new doughnut it is....But does any one know if there is an uprated one available anywhere that might have a bit better life expectancy???

i would imagine its possible to make them tougher, like with uprated bushes....Polybush etc.

kris
Logged
dirt+water= MUD :-)

www.slroc.com

Offline Jake

  • Regional Rep
  • *
  • Posts: 5474
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • <insert witty comment here>
    • South Molton, Devon. UK
  • Referrals: 0
Rear prop shaft?
« Reply #7 on: July 08, 2007, 19:34:05 »
I'm not aware of an upgraded version doughtnut tbh, but i could be wrong
Just make sure when you fit your new one, you fit it the right way round.
(there are arrows on the doughnut deplicting the direction of the bolts)
Logged
Jake

Owner - Land Rover Discovery 2
Driver - Land Rover Defender 100" Trayback

Offline KingWolf

  • Posts: 883
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
    • Spalding, Lincs
  • Referrals: 0
Rear prop shaft?
« Reply #8 on: July 08, 2007, 19:38:06 »
What would happen if you fitted it the wrong way round? When I did mine earlier in the year I never noticed any marking so just slapped it on.

Mark.
Logged
96' Discovery XS TDI with Muds, Lightbar, Snorkel, Guardian Tank Guard, Steering Guard, Wading Kit, Winch Bumper and Winch...!!!! Lift kit next..... :-)

Offline Range Rover Blues

  • Moderator
  • ***
  • Posts: 15218
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +3/-0
    • South Yorkshire
  • Referrals: 0
Rear prop shaft?
« Reply #9 on: July 13, 2007, 17:43:06 »
Just buy the propper GKN one, not a Britpart, soirry but mine ate that within the year.  Mind you I took it to Propshaft Technology in Rotherham (thanks Bulli) and they fitted a new inner support bush too, worth doing.
Logged
Blue,  1988  Range Rover 3.5 EFi with plenty of toys bolted on
Chuggaboom, 1995 Range Rover Classic
1995 Range Rover Classic Vogue LSE with 5 big sticks of Blackpool rock under the bonnet.
Pages: [1]   Go Up
 





SimplePortal 2.3.5 © 2008-2012, SimplePortal