Pages: [1]   Go Down

AuthorTopic: EGR VALVE  (Read 788 times)

0 Members and 1 Guest are viewing this topic.

Offline ross501

  • Posts: 183
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
EGR VALVE
« on: August 15, 2007, 17:40:48 »
i have a blanking plate for the egr valve and not to sure as where it goes do i just take the piece off that goes to the air inlet or do i take the whole valve off and put the blank on the manifold has anyone got any photos
Logged

Offline L90OOK

  • Posts: 1252
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
    • Somerset
  • Referrals: 0
EGR VALVE
« Reply #1 on: August 15, 2007, 17:55:11 »
You should blank it off on the exhaust manifold.  Remove all the unwanted pipework.  I also replaced the EGR valve with this:
http://www.devon4x4.com/shop.php?mode=productview&product=222

 8)
Logged
Did everyone see that?  Because I will NOT be doing it again!

 

Offline ross501

  • Posts: 183
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
EGR VALVE
« Reply #2 on: August 15, 2007, 17:58:52 »
should of mentioned its a  300tdi
Logged

Offline Ja1983

  • Posts: 1082
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • This week I have mostly been fixing....
  • Referrals: 0
EGR VALVE
« Reply #3 on: August 15, 2007, 20:07:55 »
not touched the disco yet, but i found a 2p piece fit nicely in the oriface where the two pipes meet, removed the vac hose (and blocked off)... hey presto!
Logged

It has been said that, given enough time, a million monkeys bashing at a million typewriters would eventually produce the complete works of Shakespeare. Thanks to the Saxo forums, we now know this to be wrong

No oil leek = No oil left!

Offline ross501

  • Posts: 183
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
EGR VALVE
« Reply #4 on: August 15, 2007, 21:14:49 »
so where do i put the blanking plate anyone with a pic would be a great help
Logged

Offline Range Rover Blues

  • Moderator
  • ***
  • Posts: 15218
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +3/-0
    • South Yorkshire
  • Referrals: 0
EGR VALVE
« Reply #5 on: August 16, 2007, 00:43:05 »
I put mine on the joint with the top air hose, it's the easiest to undo without snapping anything and it really doesn't matter where you fit it as long as you fit it :D
Logged
Blue,  1988  Range Rover 3.5 EFi with plenty of toys bolted on
Chuggaboom, 1995 Range Rover Classic
1995 Range Rover Classic Vogue LSE with 5 big sticks of Blackpool rock under the bonnet.

Offline Frankie-Boy

  • Administrator
  • *****
  • Posts: 2254
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +5/-0
  • Hello to anyone lol
    • Northampton, UK
  • Referrals: 0
EGR VALVE
« Reply #6 on: August 16, 2007, 03:06:38 »
Here's a photo of where mine was fitted.
Logged
Frank Bayley,
Administrator
email:- frank.bayley@ntlworld.com

thebfg2003

  • Guest
EGR VALVE
« Reply #7 on: August 16, 2007, 11:31:07 »
Thats where I fitted mine. Took 5 mins. Didnt notice any change at first but after a couple of hundred miles, greatly reduced smoke and slightly more power.  5 quid from fleabay, no regrets.

Kev
Logged

Offline Range Rover Blues

  • Moderator
  • ***
  • Posts: 15218
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +3/-0
    • South Yorkshire
  • Referrals: 0
EGR VALVE
« Reply #8 on: August 16, 2007, 11:37:49 »
That's where mine is too.
Logged
Blue,  1988  Range Rover 3.5 EFi with plenty of toys bolted on
Chuggaboom, 1995 Range Rover Classic
1995 Range Rover Classic Vogue LSE with 5 big sticks of Blackpool rock under the bonnet.

Offline cardiff_gareth

  • Posts: 461
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
EGR VALVE
« Reply #9 on: August 16, 2007, 13:36:11 »
I took off all the EGR valve pipe work and also the top intercooler hose and fitted a 300tdi defender top intercooler hose and bolted the plate to the exhause manifold where the EGR vale used to sit in.
Logged
Moved over to the dark side - Suzuki's !

Offline ross501

  • Posts: 183
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
EGR VALVE
« Reply #10 on: August 16, 2007, 21:55:13 »
done it today took the whole valve off and put the blank over the hole made a lot of difference to the performance
Logged
Pages: [1]   Go Up
 





SimplePortal 2.3.5 © 2008-2012, SimplePortal