Pages: [1]   Go Down

AuthorTopic: which head gasket???  (Read 1893 times)

0 Members and 2 Guests are viewing this topic.

Offline treeman

  • Posts: 85
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
which head gasket???
« on: December 20, 2007, 19:15:02 »
time to do the head gasket but theres a choice of 4, how can i tell which one i need??? can i find out by the engine number or do i have to take it off to see how many little holes its got if its got any??  :roll:
Logged
disco 300tdi (berry) snorkle, lightbar, steering guard, winch & winch bumper unfortunatly for sale

Offline Ralph

  • Posts: 113
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
which head gasket???
« Reply #1 on: December 20, 2007, 19:30:23 »
measure how much the pistons protrude from the engine block tell dealer and hey presto he should give you the right gasket
Logged

Offline hairyasswelder

  • Posts: 1351
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • It's gonna cost ya
  • Referrals: 0
which head gasket???
« Reply #2 on: December 20, 2007, 19:40:53 »
Have looked at rave disk but only have info for 300 tdi  :(
It states the same gasket to be fitted unless the head, crank or pistons have been replaced.
it will have 0 - 3 holes in the gasket

Hope this helps

Steve
Logged
'88 RR 3.5 efi, an on going project :o) evolving daily/slowly

Offline hairyasswelder

  • Posts: 1351
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • It's gonna cost ya
  • Referrals: 0
which head gasket???
« Reply #3 on: December 20, 2007, 20:13:15 »
Ok Jess is here  8)  she knows how to use this modern techy stuff  :shock:

May need 42" monitor or paste them  :wink:
Logged
'88 RR 3.5 efi, an on going project :o) evolving daily/slowly

Offline L90OOK

  • Posts: 1252
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
    • Somerset
  • Referrals: 0
which head gasket???
« Reply #4 on: December 20, 2007, 20:42:59 »
If it's 200Tdi fit the 3 hole thicker gasket  8)
Logged
Did everyone see that?  Because I will NOT be doing it again!

 

Offline J B

  • Posts: 457
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
which head gasket???
« Reply #5 on: December 20, 2007, 21:14:35 »
landy dealers fit the 3 hole as a matter of course
Logged
300tdi disco

Offline beast5680

  • Regional Rep
  • *
  • Posts: 2938
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
    • hailsham east sussex
  • Referrals: 0
which head gasket???
« Reply #6 on: December 20, 2007, 22:15:15 »
as ^^^^^ fit the three hole one
Logged
Neal

let him that hath understanding reckon the number of the beast

He, who laughs last, laughs best. He who laughs at Chuck Norris dies.

Offline chris9119

  • Posts: 1400
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • The New Big Boy, Gert...
    • Lordswood, Kent
  • Referrals: 0
Re: which head gasket???
« Reply #7 on: December 21, 2007, 05:53:12 »
Quote from: "treeman"
time to do the head gasket


Why is it time  :?:

Are you having the head checked at the same time...., could save loads of time/expense.

Head gaskets don't usually just go on there own...., something contributes to it going  :idea:
Logged
Chris
Si hoc adfixum in obice legere potes, et liberaliter educatus et nimis propinquus ades

http://members.mud-club.com/profiles/chris9119/gallery

Mud-Clubbers do it on channel 30





Offline treeman

  • Posts: 85
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
which head gasket???
« Reply #8 on: December 21, 2007, 08:44:31 »
iv already gone an got a crack detection kit an my mate skims, ports an gas flows heads at work so he can check it with a straight edge :lol: isnt the 3 holed 1 the safe bet being the thicker 1? i dont really wanna lose any performance because its sluggish now :oops:  looks like the dti testers coming out  :lol:  :lol:  thanks for the advice
Logged
disco 300tdi (berry) snorkle, lightbar, steering guard, winch & winch bumper unfortunatly for sale

Offline dave_2A_2.25Turbo

  • Posts: 811
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
which head gasket???
« Reply #9 on: December 21, 2007, 09:08:28 »
You can see how many holes/notches the current gasket has if you look at the bit that sticks out above the lift pump (AFAICR).  If in doubt fit the the 3-hole as the safe bet.

And  head gaskets do fail just through age.  Did mine without skimming etc and no further probs (at least - not with the gasket!), but then I didn't let it overheat.
Logged
Dave
1963 S2A
1992 Disco 200TDi
Sankey Widetrack

Offline treeman

  • Posts: 85
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
which head gasket???
« Reply #10 on: December 21, 2007, 09:40:22 »
il go an have a look now, il get a gasket set just in case anywy il prob need it one day  :lol: the previous owner hardly used it an now im jus like a kid with a big toy so it wouldnt suprise me if it had gone :lol: cheers for that, i would of took it apart 1st otherwise :roll:
Logged
disco 300tdi (berry) snorkle, lightbar, steering guard, winch & winch bumper unfortunatly for sale

Offline Range Rover Blues

  • Moderator
  • ***
  • Posts: 15218
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +3/-0
    • South Yorkshire
  • Referrals: 0
which head gasket???
« Reply #11 on: December 23, 2007, 13:55:20 »
Quote from: "jon boy"
landy dealers fit the 3 hole as a matter of course


Which is reasuring, NOT!

there's a reason why 3 or 4 thicknesses are available, though I'm told the 3 hole (next to thickest) is the most common.

Perhaps this is why so many TDis do so badly on fuel economy :?
Logged
Blue,  1988  Range Rover 3.5 EFi with plenty of toys bolted on
Chuggaboom, 1995 Range Rover Classic
1995 Range Rover Classic Vogue LSE with 5 big sticks of Blackpool rock under the bonnet.

Offline L90OOK

  • Posts: 1252
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
    • Somerset
  • Referrals: 0
which head gasket???
« Reply #12 on: December 23, 2007, 17:58:58 »
If the head has been skimmed then you will lose very little by fitting a 3 hole gasket.

Here's mine when I decided to change it  :oops:  :roll:  :lol:
There was no other damage to the engine...head gas flowed & skimmed though :twisted:
Logged
Did everyone see that?  Because I will NOT be doing it again!

 

Offline treeman

  • Posts: 85
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
which head gasket???
« Reply #13 on: December 24, 2007, 17:59:13 »
looked between the 3rd an 4th injector an it was the 1 hole gasket, its all ordered up now, thanks again  :D
Logged
disco 300tdi (berry) snorkle, lightbar, steering guard, winch & winch bumper unfortunatly for sale

Offline Range Rover Blues

  • Moderator
  • ***
  • Posts: 15218
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +3/-0
    • South Yorkshire
  • Referrals: 0
which head gasket???
« Reply #14 on: December 27, 2007, 16:16:16 »
Quick warning folks.

Some "people" were selling 3-hole gaskets on flea-bay that only had one hole in them, something to do with the tooling :roll:
Logged
Blue,  1988  Range Rover 3.5 EFi with plenty of toys bolted on
Chuggaboom, 1995 Range Rover Classic
1995 Range Rover Classic Vogue LSE with 5 big sticks of Blackpool rock under the bonnet.
Pages: [1]   Go Up
 





SimplePortal 2.3.5 © 2008-2012, SimplePortal