Pages: [1]   Go Down

AuthorTopic: How to bleed a Clutch slave cylinder?  (Read 896 times)

0 Members and 3 Guests are viewing this topic.

Offline dan3411

  • Posts: 63
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
How to bleed a Clutch slave cylinder?
« on: January 14, 2009, 14:21:55 »
Guys I know this sounds stupid.. I have finally got all the right pieces on.

it has been 2 slave cylinders and about 5 steel pipes..
describe the exact process to bleed it?  what i have been doing using.. one of those one man bleeding kits is.. attach the bleeding hose.
loosen bleed nipple. make sure reservoir is full.. and pump clutch like avery other second smoothly. whilst making sure that reservoir remains fullish. (thus not letting air back into the system) and some times i can see fluid going down the pipe but then it just stops.... why?
Logged
Disco '91 3dr 200Tdi

Offline dan3411

  • Posts: 63
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: How to bleed a Clutch slave cylinder?
« Reply #1 on: January 14, 2009, 14:36:03 »
No worries all done

it wouldn't bleed because it was on axle stands  :oops:


[edit] Excuse the spelling mistakes got abit excited :D
« Last Edit: January 14, 2009, 21:42:19 by dan3411 »
Logged
Disco '91 3dr 200Tdi

Offline clover

  • Posts: 550
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Clover
  • Referrals: 0
Re: How to bleed a Clutch slave cylinder?
« Reply #2 on: January 14, 2009, 18:24:17 »
Usually take 3 people - one in the car working the clutch pedal, one keeping the fluid topped up, and one operating the nipple on the cylinder. I reckon you neither need to put you finger over the nipple or have a pipe and a bottle half full of fluid on the end.   
Logged
1996 Discovery 300TDi Affectionately known as Clover. 
Cooper Discover STT 33/12.50/R15, a 2" body lift off chassis. H/D springs with 50mm platform spacers on the rear. Nothing on the front as they foul the shocks :-) 11" travel rough country shocks and mountings with dislocating spring cones,  adjusted wheel arches, safari snorkel. H/D rear bumper, demountable drop plate,. H/D steering guard, QT diff guards.
tree sliders, Split charge running twin Optima's, spotlight bar with 4 whoppers on it, H/D winch bumper, 12,000lbs winch,  A bar with 2 50w mini spotlights, brownchurch full length roof rack. 2 work lights.CB,
Fine English engineering modified to work!

Offline discorich

  • Posts: 96
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: How to bleed a Clutch slave cylinder?
« Reply #3 on: January 14, 2009, 21:33:21 »
ahhh that is useful, i am just about to do this as my slave cylinder gave out at a trial the other week, not fun having to turn the engine off to select reverse, hehehe.

cheers guys, if i have any problems you will read it on here, hehe.
Logged
When i get stuck, i am just providing every one around recovery experience, how generous!

Offline dan3411

  • Posts: 63
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: How to bleed a Clutch slave cylinder?
« Reply #4 on: January 14, 2009, 21:48:10 »
Quote from: discorich on January 14, 2009, 21:33:21
ahhh that is useful, i am just about to do this as my slave cylinder gave out at a trial the other week, not fun having to turn the engine off to select reverse, hehehe.

cheers guys, if i have any problems you will read it on here, hehe.

Some advise that i would have liked when i initially started mine (cheers Fruitloop)..

1) pull the hose to the top of the engine bay and attach the slave cylinder to the dampener. then the whole thing into the bellhousing.

2) Tighten the steel pipe in to the slave cylinder and the dampener at the same time. or you will end up [!Expletive Deleted!] up the pipe (like me  :oops:)
Logged
Disco '91 3dr 200Tdi

Offline discorich

  • Posts: 96
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
  • Referrals: 0
Re: How to bleed a Clutch slave cylinder?
« Reply #5 on: January 21, 2009, 19:14:17 »
Hey there, i have heard that there is no need to refit the dampner, it this a myth or is it possible, i have also been told thatit works better without the dampner.

cheers for your help dan3411.

I will try that when i get round to fitting it.
Logged
When i get stuck, i am just providing every one around recovery experience, how generous!

Offline Range Rover Blues

  • Moderator
  • ***
  • Posts: 15218
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +3/-0
    • South Yorkshire
  • Referrals: 0
Re: How to bleed a Clutch slave cylinder?
« Reply #6 on: January 21, 2009, 19:32:30 »
The damper is a PITA, but it's there for a reason.
Logged
Blue,  1988  Range Rover 3.5 EFi with plenty of toys bolted on
Chuggaboom, 1995 Range Rover Classic
1995 Range Rover Classic Vogue LSE with 5 big sticks of Blackpool rock under the bonnet.
Pages: [1]   Go Up
 





SimplePortal 2.3.5 © 2008-2012, SimplePortal