Pages: [1]   Go Down

AuthorTopic: Head Gasket (Best one) ?  (Read 11313 times)

0 Members and 1 Guest are viewing this topic.

Offline Big G

  • Posts: 130
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-1
  • Referrals: 0
Head Gasket (Best one) ?
« on: October 16, 2012, 16:37:07 »
Looks like I have a light oil leak from the head Gasket so I have been
looking into whats involved in changing it. One question I cant decide on is which is the best replacement? Any reccomendations please.
Logged

Offline lambert

  • Moderator
  • ***
  • Posts: 2137
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +1/-0
  • and then as if by magic
    • harrogate
  • Referrals: 0
Re: Head Gasket (Best one) ?
« Reply #1 on: October 16, 2012, 20:13:26 »
Are you sure its your head? Is be very worried if it were, is there any contamination of oil or water, is it running hot?
Logged
Lambert Coverdale.

As slow as possible, as fast as necessary.

Two and a half litres of turbocharged diesel goodness.

Offline Big G

  • Posts: 130
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-1
  • Referrals: 0
Re: Head Gasket (Best one) ?
« Reply #2 on: October 16, 2012, 20:59:42 »
Lambert,

I noticed a build up of oil over a long period of time. As you look at the engine its on the right side underneath the exhaust manifold. Last week I degreased and washed off the engine and now after a few days the damp patch has started to re appear and its origin is at the block and head joint. Theres no loss of water. No bubbles in water. The temp guage never gets past less than a quarter off the cold mark and thats on a short run up the motorway (8 miles). The oil is not contaminated with water either. Engine (300Tdi) starts and runs lovely.
Logged

littlepow

  • Guest
Re: Head Gasket (Best one) ?
« Reply #3 on: October 18, 2012, 20:22:07 »
Logged

Offline Devon-Rover

  • Posts: 748
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-0
    • Tavistock
  • Referrals: 0
Re: Head Gasket (Best one) ?
« Reply #4 on: October 19, 2012, 19:51:03 »
Have an ask at the parts places and see if the allmakes gasket set still use Victor Reinz gaskets. That is an OEM quality set up.
Logged
Rowan.

"Jemima" 2.25 Petrol SWB, ACR rear Silencer, 235/85 Macho's, MAP Capstan & HD Bumper, Tweeked suspension, CB, Light Bar.
"Baker" 2.6 Petrol LWB (former Tow Truck)
"Lizi" 4.2 V8i Discovery, Gone but not forgotten.
"Kate" 1985 Ninety 4.2 V8 Auto, Stainless exhaust, Ashcroft Tunnel, Mud console, Polmar Venus CB, HD Steering bars, Terrafirma Steering damper, D44 Winch Bumper, Superwinch EP9.5, Superwinch Wireless controls, QT Diff Guards. 'More toys to come'


Vorsprung Duch Ducktape. My website Searle Safari Info source.

Offline Big G

  • Posts: 130
  • Attack: 100
    Defense: 100
    Attack Member
  • Karma: +0/-1
  • Referrals: 0
Re: Head Gasket (Best one) ?
« Reply #5 on: October 19, 2012, 20:32:13 »


Ok so far I have one reccomendation for Elring and one says Victor Reinz is good quality.

Logged
Pages: [1]   Go Up
 





SimplePortal 2.3.5 © 2008-2012, SimplePortal